Pentax K-mount

Pentax K-mount

Pentax K1000 without lens, showing the original K mount
Type bayonet
Tabs 3
Connectors electrical pins, drive shaft for focus.

The Pentax K-mount, sometimes referred to as the "PK-mount", is a bayonet lens mount standard for mounting interchangeable photographic lenses to 35 mm single-lens reflex (SLR) cameras. It was created by Pentax in 1975,[1] and has since been used by all Pentax 35 mm and digital SLRs (with the exception of the medium format 645D and 645z), as well as the MILC Pentax K-01. A number of other manufacturers have also produced many K-mount lenses and K-mount cameras.

Mounts

The Pentax K-mount has undergone a number of evolutions over the years as new functionality has been added. In general, the term K-mount may refer to the original K-mount, or to all its variations.

Originally designed by Zeiss for an alliance with Pentax , it was intended to be a common lens mount for a proposed series of cameras and lenses. However, the plan failed to work out and the two firms parted company amicably, but Pentax retained the lens mount and at least one Zeiss lens design for its own use.

K-mount

The original K-mount is a simple bayonet connection with three tabs. It was introduced with the K series of cameras. The lens is locked into the camera with an approx. 70° clockwise turn (when looking at the front of the camera).

The only linkage with the camera is mechanical and involves the aperture. A slot between two of the bayonet tabs on the lens allows the stop-down coupler from the camera to sense the aperture setting on the lens and adjust the light meter display accordingly. Opposite this is the diaphragm release from the lens which extends into the camera body and holds open the spring-loaded diaphragm of the lens. When setting up a shot this keeps the diaphragm fully open. When the shutter is released, so is this lever. It allows the diaphragm to close to the desired setting while the film is being exposed, and opens it again after the shutter closes.

Both of these linkages are arranged so that they are aligned and spring-loaded by the act of inserting the lens and turning it until it locks.

Bodies equipped with the original K-mount include the K series, the M series except the ME F, and the LX. Lenses that support it include those labelled 'SMC Pentax', 'SMC Pentax-M' and 'SMC Pentax-A'. These K-mount bodies cannot use lenses that lack an aperture ring, such as FAJ or DA.

K-mount lenses can be used on all Pentax bodies, but are restricted to stopped down mode when used with "crippled" KAF-mount bodies (see below).

KF-mount

Pentax ME F and SMC Pentax-AF 35-70/2.8, the only products using the KF-mount.

The KF-mount was Pentax's first attempt at an autofocus system. This autofocus system used sensors in the camera body and a motor in the lens. The two were connected via five new electrical contacts on the bayonet mount itself. One permitted the lens to turn on the camera's metering and focus sensors, two focused the lens (towards and away from infinity) and two appear to have been unused and may have been reserved for future functionality.

The KF-mount was largely a failure. Only one camera and one lens ever used this mount, the Pentax ME F and SMC Pentax-AF 35-70/2.8. The lens was somewhat large and cumbersome since it had to enclose both the focusing motor (with gears) and batteries to power it. KF and the ME-F are similar in many ways to the system used by Canon in the ill fated Canon T80, introduced several years later.

The ME F can use all Pentax K-mount lenses which feature an aperture ring. The 35–70 mm lens can be used on all other Pentax K-mount bodies in manual focus mode, but it must be used stopped down on "crippled" KAF bodies.

KA-mount

Pentax A 50 mm lens displaying the KA-mount

The KA-mount is derived from the original K-mount. It allows the lens's aperture to be set by the body, and thus permits shutter priority and program auto exposure modes. It was introduced in 1983, and is supported by A-series and P-series bodies; Pentax lenses that support it are marked 'SMC Pentax-A'. It is completely backward-compatible with the original K-mount.

The aperture on the lens is set from the body by the same stop-down lever found on the original K-mount, but on KA-lenses this lever is proportional to the area of the aperture opening, rather than the diameter as on previous lenses. This allows the body to easily set a specific aperture, since the relationship to F stops is linear. The lenses add an 'A' setting on the aperture dial, which gives the body control of the aperture. Other, numeric settings are used for manual aperture modes—aperture priority and full manual mode.

Six electrical contacts are added to the bayonet ring. One is slightly recessed and allows the lens to indicate whether the aperture ring is set at 'A' or not. If it is, a pin on the lens extends slightly and makes contact, while if the lens is at any other setting the pin is retracted and does not make contact. The other five contacts are used to encode the lens's aperture range. Each contact on the lens is either conducting or non-conducting, providing a binary 1 or 0, respectively. Two contacts encode the lens's minimum aperture—f/16, f/22, f/32 or f/45; although no Pentax K-mount lens has ever had an f/16 minimum aperture, OEM lenses often have. The other three contacts encode the lens's maximum aperture; their meaning is dependent on the minimum aperture indicated by the lens.

KAF-mount

The KAF-mount was Pentax's second and much improved attempt at adding auto-focus to lenses. It adds a small drive shaft to the KA-mount, allowing the body to adjust the focus of the lens. This makes the lenses less bulky than the earlier KF-mount, which had both a motor and batteries inside the lens.

It also adds a seventh electrical contact, this one carrying digital information from the lens to the camera. It carries the following information: focal length, distance to the subject, exact absolute f-stop value, and lens size. This information is used to make better exposure decisions, along with the multi-segmented metering that was introduced in cameras using the KAF-mount.

The MZ-30/ZX-30, MZ-50/ZX-50, MZ-60/ZX-60, the *ist series and the K100D/K110D lack the mechanical stop-down coupler/indicator. In these cameras – in aperture priority mode – the aperture is set by a dial on the camera body, and no longer on the lens. Pre-A lenses can only be used in manual stop down metering mode and manual flash mode.

KAF2-mount

Pentax KAF2 mount (body and lens). 1. alignment marker 2. locking pin 3. lens release button 4. digital lens information contact 5.–10. electrical lens information contacts 11. aperture control lever 12. power contacts 13. screw-drive auto focus drive shaft 14. aperture simulator

The KAF2-mount is the same as the KAF-mount except that it adds two extra power contacts to the inside of the mounting ring and transmits modulation transfer function (MTF) data through the digital seventh contact. The power contacts were originally used for power zooming. Since the introduction of the K10D digital SLR model, they are mainly used for powering Silent Drive Motor and DC motor lenses.

The K10D/K100D Super and later cameras do not have a mechanical stop-down coupler/indicator and thus can only use stop-down metering on pre-A lenses.

KA2-mount

The KA2 is identical to KAF, but lacks the autofocus drive shaft. Another way of looking at it is that it adds the seventh contact for digital information to the KA-mount.

KAF3-mount

The KAF3-mount is used on Pentax lenses that solely rely on SDM or DC autofocus motors. It is identical to the KAF2, but lacks the screw-drive autofocus drive shaft.[2] Another way of looking at it is that it adds the power zoom/in-lens autofocus motor contacts to the KA2 mount.

KAF4-mount

The KAF4-mount was introduced in June 2016 with the HD Pentax-DA 55-300mm F4.5-6.3 ED PLM WR RE lens. It is identical with KAF3, apart from the missing aperture control lever. Instead, aperture control information is transmitted digitally through the data pin and the aperture is stopped down through a motor built into the lens. It also introduced a new type of autofocus motor, designated PLM or Pulse Motor. At the time of its introduction, the following Pentax DSLR bodies were compatible with the new mount: K-70, K-50,K-S2, K-S1, K-1, K-3 II, with all but the K-70 requiring a firmware update. Also after a recent firmware update the original K3 can use the new mount.[2]

“Crippled” K-mount

All digital K-mount Pentax SLR bodies as well as some lower-end film cameras lack the ability to read the position of the aperture simulator. This means that lenses that lack the lens information contacts introduced with the KA-mount (Pentax K- and M-series lenses as well as some third-party products) do not support open-aperture metering on these bodies. Instead, stop-down metering must be carried out by pushing the “green button” on the camera before taking a shot. This variation of the mount is commonly referred to as the “crippled“ K-mount.[2]

R-K-mount

The R-K-mount is a variation on the original K-mount by Ricoh. It supports Ricoh's own implementation of shutter priority and auto exposure modes, similar to the KA-mount but much simpler. The only addition to the original K-mount is a small pin, commonly dubbed Ricoh pin,[2] at the bottom which tells the body when the aperture ring has been set to the "P" setting (similar to the "A" setting on Pentax KA lenses). The 'P' setting is not compatible with the 'A' setting as the 'P' pin is in a different location than the 'A' contact on Pentax 'A' lenses and the flange on Pentax bodies.

The R-K-mount is used on Rikenon P lenses, Ricoh bodies that include the letter 'P' in their model number, and some non-Ricoh lenses. It is compatible with all other K-mount cameras and lenses when in manual or aperture-priority exposure modes, however the extra pin needs to be removed for safe use on autofocus Pentax cameras. The reason for this is, that the extra pin is located at the same place as the shaft used for screw-drive auto focus, where it can get locked.[2] Lenses locked to the camera body this way are difficult to remove and may require complete dismantling.

Adaptors to use on K-mount

L39 / LTM

Adaptors can be found to allow use of lenses with Leica M39 thread (screw) mount. If a lens originally intended for Leica Rangefinder cameras is used, focusing is limited to about 10 cm. However, some SLR lenses were made in LTM 39 mount, mostly by KMZ for use in the early Zenit SLRs which had LT 39 mounts. These "Zenit" TM 39 lenses will focus properly. Or these lenses can be used in conjunction with the M42 to LTM 39 adapter.

M39

Adaptors can be found to allow use of a non-Leica 39 mm mount into the K-mount, typically as a M39-M42 adapter ring that is mounted in a M42-PK adapter; they may focus to infinity.

M42

Pentax supplies adapters to fit M42 screw-mount lenses, as do several third-party manufacturers. The M42 screw-mount system was used by Pentax prior to the introduction of the K-mount. Pentax designed the K-mount wide enough to allow an adapter to fit between the M42 thread and the K bayonet. They also kept the same flange focal distance (also called registration distance or register) as the M42 screw-mount, so that M42 lenses focus correctly using the correct adapter (such as Pentax original[3] or Bower). There are however other third-party adapters that add to the flange focal distance so that one loses the ability to focus to infinity. The loss of infinity-focus may not be significant in macro or close-up photography.

There is great debate in the Pentax community over the applicability and safety of adapters other than those supplied by Pentax. Many users of third-party infinity-focus adapters, such as Bowers, report difficulty in removing the adapters from camera bodies. Such adapters may require modification before they may be safely used. Official Pentax adapters, and flanged non-infinity-focus adapters, do not provoke such problems.

Many old M42 lenses have a modern-day cult reputation, including the (Pentax) Asahi Takumar range. Some manufacturers, including Carl Zeiss AG, still make lenses in the M42-mount. K-mount cameras have a suitable flange focal distance (45.46 mm) to adapt old M42 lenses without any optical correction or loss of infinity focus/changed close focus distance. Other SLRs with a short flange-focal distance can accept M42 lenses as well: Canon E-mount (44.00 mm), Sony and (Konica) Minolta A-mount (44.50 mm), Sigma (44 mm), Olympus 4/3rd (38.67 mm), and many more, but notably not Nikon F-mount (46.5 mm).

Nikon AI/AIS

Optically corrected adapter to use Nikon AIS AI lenses on K-mount.

Voigtländer Bessamatic / Kodak Retina

Adapter for Voigtländer Bessamatic and Voigtländer Ultramatic lenses, Kodak Retina Reflex, or Kodak Retina IIIs lenses.

Petri

There is also some Petri adapter to K-mount but those do not allow to focus to infinity due to the different flange-to-film-plane distance.

Medium format

Pentax made adapters for its medium-format lenses to use on the K-mount, both the 645 and 6×7, and for the Hasselblad Bayonet type. Also there is a Pentacon-Six (Kiev88 CM) adapter still in production and a shift adapter to use Pentacon lenses as shift lens.

T-mount

Mounts used for Telescopes, microscopes and generic optics. The T-mount was initially developed by Tamron (1957) to allow the easy adaption of generic 35 mm SLR optics into multiple mounts. The T-mount is a 42 mm diameter 0.75 mm pitch screw mount with a 55 mm flange focal distance. Later versions (T2, T4, TX) were more advanced and complex. Several other manufacturers besides Tamron have used these mounts. Because the T-mount is still used for many telescopes and microscopes, they are still available new. Note that while both T-mount M42-mount are both 42mm screw-mount screw mount systems, and will mount if they are forced, they are not compatible. The difference in pitch can cause damage to the lens, adapter or camera mount if they are confused.

Adaptall

These are adaptors designed by Tamron to allow the transfer of aperture setting from lens to camera or vice verse, including the Adapt-A-matic (1969), Adaptall (1973) and Adaptall-2 (1979). When Pentax introduced the KA-mount in 1983 Tamron upgraded their Adaptall-2 K-mount into an Adaptall-2 KA-mount. For more details see the Tamron article or the Adaptall-2 web site.[4]

Adaptors for other cameras to use K-mount

Cameras

Pentax

Manual focus

  • K – K2, KX, KM, K1000, K1000 SE
  • K – ME, ME SE, ME Super, ME Super SE, MG, MV, MV1, MX
  • K – LX
  • KA – Super A, Program A/Program Plus, A3
  • KA – P3, P5, P30, P30n, P30t
  • KA2 – MZ-M

Auto focus

Almaz

  • 101
  • 102
  • 103
  • 104

Chinon

  • CE-4, CE-4s, CA-4,CA-4s, CM-4, CM-4s
  • CE-5, CG-5, CM-5, CP-5, CP5s
  • CP-6, CP-X
  • CP-7m, CM-7
  • CP-9AF

Carena

  • KSM-1

Cimko

  • ksx sears 35 mm film and a 50 mm lens

Cosina

  • C1, C1s
  • CS-2, CS-3
  • CT-10, CT-1A, CT-20, CT-7, CT-1G, CT-9, CT-4
  • CE-4, CE-4s, CE-5

Edixa

  • CX 5

Exakta

  • KE 5

Lindenblatt

  • KL-2

Miranda

  • MS-1
  • MS-2 Super
  • MS-3

Porst

  • Compact Reflex OC
  • Compact Reflex OCN

Promaster

  • Promaster 2500 PK

Quantaray

  • D2-RZ

Ricoh

  • KR-5, KR-5 Super, KR-5 Super II, KR-5 III, KR-10, KR-10 Super, KR-30sp
  • XR-1, XR-1s, XR-2, XR-2s, XR-500, XR500 auto, XR-6, XR-7, XR-10, XR-P, XR-20sp, XR-Solar, XR-M, XR-F, XR-P, XR-S, XR-X, XR-X 3PF

Samsung[5]

  • "crippled" KAF - GX-1S, GX-1L
  • "crippled" KAF2 - GX-10, GX-20

Sears

A lot of Sears cameras were made by Ricoh or Chinon and use the Pentax K-mount. Some are simply rebadged models, while others are quite different.

  • KS-1000 (Ricoh XR-1)
  • KS-500 (Ricoh XR-500)
  • KS Auto (Ricoh XR-2S)
  • KS-1
  • KS-2 (Ricoh XR-7)
  • KSX (Ricoh KR-10)
  • KSX-P (Chinon CP-5)
  • KS Super
  • KS Super II

Sigma

  • SA-1

Topcon

  • RM300

Vivitar

  • V4000
  • V3800N
  • V3000N
  • V3000s
  • V2000
  • XV1 (rebadged Cosina CT-1)
  • XV20 (rebadged Cosina CT-20)

Cosina Voigtländer

Zenit

  • Automat, 20, 21, 22, 14, photosniper FS-5
  • AM, AM2, AP, 2000, APK, KM, 122K, 212K

List of lenses with any K-mount variant

Access

Angenieux

Angenieux a lens manufacturer in France, mainly known for its movie equipment than for photographic lenses, but it has built optics for Leica, Nikon, Canon and a few K-mount lenses.

Agfa

The Agfa K mount cameras were rebadged Chinons.

Arsat

Arsat is a trade mark of Ukrainian lens manufacturer Arsenal, Kiev.

Beroflex

Beroflex seems to have been a German commercial firm of photographic lenses; not too much information is available yet but it appears that it designed lenses made overseas by Japanese companies like Soligor.

Carl Zeiss Jena

Carl Zeiss of East Germany marketed a number of lenses for the K-mount through its sales network. These lenses were in fact made by Sigma in Japan. The "real" 35 mm East German made Carl Zeiss Jena Lenses where available at the same time but only in Praktica B-mount.

Carl Zeiss

Carl Zeiss is one of the most prestigious names on the photographic world; it re-launched its line of lenses for the K-mount in 2008, mainly due to the growing popularity of both Pentax and Samsung digital SLRs. Carl Zeiss announced in September 2010 that the ZK lenses would be discontinued that year.

Chinon

Cima Kogaku

Cima Kogaku had a patented[6] system that allowed them to build common lens bodies, and add the appropriate lens mount at the factory. The Pentax version was only K-mount, not KA-mount. They mostly sold their lenses on an OEM basis, with them sold under a variety of different brands. In the UK, they were sold by Photax as Super-Paragon PMC lenses. Tokyo Kogaku sold them as AM Topcor lenses for their Topcon RM300 camera. Cima Kogaku also sold them directly under the Cimko brand. (Some of the lenses below may not have ever been sold under the Cimko brand.)

Cosina

Cosmicar

Cosmicar is a division of Pentax, it commercialized video lenses, but some were released for the K-mount.

CPC

CPC Lenses are also known as Phase 2 or Phase 2 CCT.

Eikor

Focal

Gemini

Hanimex

Hanimex was an Australian distributor founded by Jack Hannes after the Second World War.[7] The name is a contraction of HANnes IMport and EXport and the company imported both European and Japanese lenses, bodies and accessories. Hannes apparently sought low cost providers and Hanimex lenses have a poor reputation among users.

Hervic Zivnon

Helios

Made for the Zenit cameras by KMZ

Hoya

Hoya, a leading manufacturer of optical glass, purchased Pentax in 2008.

JC Penney

Kalimar

Kalimar was an American distributor of camera equipment from 1952 to 1999 when it was acquired by Tiffen, information on lenses and manufacturers is difficult to obtain as it sell rebadged cameras and lenses from the former Soviet Union and Japan and sell it under its own name in the United States.[8]

Kiron

Kiron was a third party lens manufacturer,[9] it manufactured lenses for other mounts as well on the decade of 1980-1990

LOMO

LOMO is a Russian photographic manufacturer, it made some lenses for the Almaz camera on K-mount, but caution must be used as the Almaz version has some differences with the standard K-mount

Lester A. Dine

Lensbaby

Loreo

Luxon

Luxon is a Chinese manufacturer, and there is little information available on the company or its products.

Mir

Miranda

Miranda was a brand name used by the Dixons group in the UK, mostly for Cosina made products.

Mitakon

Makinon

Makinon lenses were made by Makina Optical in Japan.

Oberon

Ozunon

Petri

Petri was a Japanese camera manufacturer, which tried to capitalize on the popularity of the K-mount lens base and made one camera that used the K-mount with one standard lens:

Peleng

Peleng is a lens manufacturer based in Belarus, it was founded in the Soviet era and released most of its lenses for the M42 mount, but it has a K-mount lens:

Pentax

Main article: Pentax lenses

Good sources of information on Pentax K-mount lenses: Bojidar Dimitrov's Pentax K-mount pages,[10] Stans Pentax Photography site,[11] Pentax Forum's lens reviews.[12] Bold text indicates lenses in current production/stock sale from Pentax.[13]

Special optics

Accessories

Phoenix

Polar

Polar is a brand of Samyang Optics, a South Korean third party lens manufacturer.

Porst

Promaster

Revue

Revu

Revuenon

Ricoh - Rikenon - Riconar

This lens uses the Ricoh KR-mount version, Ricoh made both a XR version without the zoom pin, and the P version which has it.[15]

Rokinon

This lens uses the Ricoh KR-mount version:

Sakar

Sakar is a commercial American company that used to sell K-mount lenses.[16]

Samyang

Samsung

Schneider-Kreuznach

All these lenses had been marketed by Samsung and are those present on Samsung's digital SLRs[17] Schneider-Kreuznach is a traditional optics maker that do still make specialised glass and lenses (today mainly high-quality large-format lenses, enlarger lens and photographic loupes), but not for Samsung. They license their name to Samsung granted that certain minimum quality requirements are fulfilled. All the Schneider branded glass from Samsung is manufactured by Pentax and corresponds directly to Pentax lenses.[18][19]

Special lenses

The Schneider-Kreuznach lenses feature shift and tilt movements for perspective control; they can be shifted by 12 mm and tilted by 8 degrees simultaneously.[20]

Sears

Sears is an American commercial company that sells relabeled lenses and cameras at their own stores in the United States for a number of years. As the objective was mainly commercial, quality is very different among lenses. Quality on construction in some ones is very good and in some others is plain bad. But it seems to be consistent among the same model. Some of the Sears lenses were made to fit Sears Cameras with the Ricoh K-mount version and are identified as KR, but is prudent to verify it before using it on more modern cameras that may be damaged by the Ricoh pin.

Sigma

Sigma is a Japanese manufacturer of cameras and lenses. It has made lenses for the K-mount for a number of years. And quality among them had varied a lot. After the launch of the K10D digital SLR it launched K-mount D series lenses. Such ones are designed to be used with the APS size camera, but older K-mount can be used as well. An increase in model numbers can be seen between 2007 and 2008 due to the success of the K10D, K100D, K100D Super, K110D, K20D and K200D cameras. Use of older Sigma lenses is possible but with caution, some Sigma older K-mount lenses are with the infamous Ricoh pin.

Soligor

Spiratone

Spiratone was a company devoted to sell photographic accessories and manage to sell some lenses under their own brand name until it closed, very few were made for the K-mount, and none of them are known to be of good quality.

Sun

Sunagor

Suntop

Takumar

Tamron

A Tamron 28-75 mm f/2.8 in Pentax K-mount

Tamron is a third party vendor of photographic lenses, quality among them varies a lot. It is important to distinguish the adaptall versions from everything else, the adaptall is a generic adapter that allowed Tamron to manufacture a single lens design for a wide range of cameras, and commercialize those for specific brands with the use of the Adaptall I and Adaptall II adapters. So there are Tamron Lenses on K-mount, and Tamron Adaptall I and II for K- and KA-mount adapters. More Information on the Adaptall can be found on the Tamron article of Wikipedia. Here the non-Adaptall versions:

Tokina

Tou/Five Star

Tou Five Star was the commercial brand from Toyo Optics; some lenses are labeled as Toyo Optics, Toyo Five Star or Tou Five Star. They were manufactured between 1967 and sometime around 1980, when the company seems to have changed its focus to video lenses.

Venus Optics

Vivitar

Cosina Voigtländer

VOMZ

Vologda Optical-and-Mechanical Plant.

Zenitar

Zenitar[22] is a Russian lens brand, made by KMZ. Most Zenitar lenses are also available in M42-mount. Some of these are sold as K-mount lenses but use an adapter.

Special lenses

References

  1. ↑ "Bojidar Dimitrov's Pentax K-mount page". Retrieved 2007-09-30.
  2. 1 2 3 4 5 "The Evolution of the Pentax K-mount – Technical Information and a Little Bit of History". pentaxforums.com. 29 December 2014. Retrieved 14 June 2016.
  3. ↑ http://www.pentaxwebstore.com/detail/PTX+30120
  4. ↑ http://www.adaptall-2.com/
  5. ↑ "Samsung Digital Camera". Samsung Techwin (subsidiary of Samsung Group). April 4, 2008. Retrieved 2008-04-05.
  6. ↑ "US Patent 4,174,167". US Patent and Trademark Office. November 13, 1979.
  7. ↑ Paul Burrows (5 October 2012). "The Australian Way". AV Hub.
  8. ↑ "Kalimar Acquisition by Tiffen with some history". unknown. February 3, 2000. Retrieved 2008-09-17.
  9. ↑ "General Reference to kiron Lenses on MFLenses". MFLenses. September 17, 2008. Archived from the original on 2008-04-18. Retrieved 2008-09-16.
  10. ↑ http://www.bdimitrov.de/
  11. ↑ http://stans-photography.info/
  12. ↑ http://www.pentaxforums.com/lensreviews/index.php
  13. ↑ http://www.pentax.jp/english/imaging/digital/lens/
  14. ↑ http://www.frtg.de/privat/porst_automatic_tele_135mm_f28/frtg_de_porst_automatic_tele_135mm_f28.htm
  15. ↑ http://www.drricoh.de/Rikenon/index.html
  16. ↑ Sakar Current Corporate website Sakar Corp.
  17. ↑ Schneider Kreuznach Site
  18. ↑
  19. ↑
  20. ↑ "Tilt/Shift Lenses".
  21. ↑ Robertstech's Vivitar Series 1 70-210 f/3.5 Zoom Lens review page
  22. ↑ http://www.zenitcamera.com/catalog/lenseslist.html

More information


This article is issued from Wikipedia - version of the 12/1/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.