Hood unit
A hood unit, in North American railroad terminology, is a body style for diesel and electric locomotives. On a hood unit, the body of the locomotive is less than full-width for most of the locomotive's length, with walkways on the outside of the locomotive. In contrast, a cab unit has a full-width carbody for the length of the locomotive. A hood unit has sufficient visibility to be operated in both directions from a single cab. Also, the underframe is the main load-bearing member, allowing the hood to be non-structural and easily opened or even removed for maintenance.
History
The hood unit evolved from the switcher locomotive. A switcher's long hood is normally low enough that the crew can see over it, and there typically is no short hood. Alco introduced the road switcher concept with the RS-1, which was an enlarged switcher with a short hood ahead of the cab. This was added to provide protection for the crew in case of a collision. The low long hood was retained, though its increased length made visibility over it useless. Later, EMD introduced the GP7, which had a similar layout, though both hoods were as high as the cab roof. The high long hood became standard for virtually all hood unit locomotives thereafter.
The long hood of a locomotive is usually about as tall as the cab roof in order to fit the large prime mover and its related subsystems. Originally the short hood of the locomotive was the same height, which is referred to as a high-nose or, confusingly, high short hood. This was originally done to avoid union conflicts, as the high nose ensured that two crewmen (one on each side of the cab) were required in order to see both sides of the track. After this issue was resolved, the height of the short hood was reduced to increase visibility, creating a low-nose or low short hood locomotive. Some locomotives that were originally built with a high nose were later modified to have a low nose. Lately it has become common to make the short hood not only lower but also full-width, creating a wider nose which is usually referred to as a North American Safety Cab.
The visibility and access advantages mean that the hood unit is overwhelmingly the most popular style of locomotive in North America, as well as many other nations.
Operation
Although the crew cabin is centered on some hood units (particularly in the case of dual, relatively small prime-movers), in most cases the cab is closer to one end of the locomotive than the other (in the case of a single, relatively large prime-mover), breaking the locomotive up into long hood and short hood sections. It is generally preferred to run a hood unit short hood forward so that the cab is closer to the front, but there is enough visibility in the other direction that they can run long hood forward at regular speeds. Some railroad companies (notably, the Norfolk & Western and the Southern) ordered locomotives with cabs facing long hood forward so that the short hood is actually the rear of the locomotives, but that practice has become increasingly rare. This was usually done to offer greater protection to the crew in the event of a collision. Other locomotives were set up with dual control stands so that they could operate in both directions, making it unnecessary to turn the locomotive around at the end of a run. Some cabless hood units were also built. The long hood ran the whole length of those locomotives. In North America, all locomotives are required to have the letter F printed on the side sill at the end which is normally operated as its front.
Freight-oriented hood units
- GE U30C
- GE U36B
- EMD GP30
- EMD SD60
- EMD SD70 series
- GE C30-7
- GE Dash 8-40BW
- EMD GP38
- EMD SD40
- EMD SD90MAC
Passenger-oriented hood units
- Brookville BL20GH
- EMD SDP45
- GE Dash 8-32BWH
- GE U34CH
- MPI MP32PH-Q
United Kingdom
The term "hood unit" is not used in the UK but a few locomotives of the hood unit type are in service:
- British Rail Class 70 (introduced 2009)
- British Rail Class 08 (introduced 1952)
- British Rail Class 09 (introduced 1959)
- British Rail Class 20 (introduced 1957)
Withdrawn hood unit types include:
France
The term "hood unit" is not used in France but a few locomotives of the hood unit type are or were in service:
- BB 63000
- BB 66000
- BB 66400
- Y 8000
Turkey
Almost all Turkish locomotives have this design. Cab units recently imported and produced under licence.