M31 HEAT rifle grenade

M31 HEAT rifle grenade

M31 HEAT rifle grenade fitted to an M14 rifle
Type Anti-armor rifle grenade
Place of origin United States
Service history
Wars Cold War
Production history
Designed late 1950s
Produced 1950s - 1960s
Specifications
Weight 709 g
Length 430 mm
Diameter 66mm/warhead
Effective firing range 115 meters/effective
Maximum firing range 185 meters/maximum
Filling Composition B
Filling weight 254 g
Detonation
mechanism
 nose-initiated, base-detonated
Marine preparing to fire M31 from M1 rifle
Cutaway of M31 HEAT rifle grenade

The M31 HEAT is a fin-stabilized anti-tank rifle grenade designed in the late 1950s to replace the Belgian ENERGA rifle grenade which was adopted by the US Army and US Marines as an emergency stop-gap measure during the Korean War. Like the ENERGA, it has a nose-initiated, based-detonated HEAT warhead, but unlike the ENERGA, the mechanical impact fuse system is replaced with a less complex and more reliable piezo-electric fuse system which also allows higher angles of impact, up to 65 degrees. On impact, the nose cover collapses, crushing a crystal-like material, which sends an electric current through a separate wire to the warhead's detonator, located in the base of the warhead. A mechanical safety, comprising a set back system located in the warhead's base, grounds the firing circuit and prevents the accidental explosion of the warhead. On firing, the sudden launch acceleration causes the set-back's three disks to rotate 90 degrees, each in succession to the other, with the rotation of the third disk removing the grounding after approximately 10 meters of flight and completing a firing circuit for the current to flow from the nose to the detonator in the base. Compared to the ENERGA, the M31 is slightly lighter in weight and has a smaller-diameter warhead—i.e. 75mm vs 66mm. Penetration for the M31 is estimated to be 200 mm / 8 inches for steel armor plating [1][2] and twice that estimate for concrete. The warhead technology developed for the M31 was used for the future M72 LAW antitank rocket.

The M31 was originally designed to be fired only from the M1 Garand, but could be fired from the M14 rifle. To launch the M31, a detachable spigot-type grenade launcher (M7A3 launcher for M1 rifle, and M76 launcher for the M14 rifle) is fitted to the muzzle of the rifle. A M3 ballistic cartridge (two are supplied in the packing container with each grenade and are crimped to indicate the cartridges are only for launching rifle grenades) is loaded into the rifle's chamber. The hollow tail unit of the rifle grenade is fitted over the grenade launcher.[3] Official military manuals recommend that the M31 HEAT be fired from either the standing or kneeling position and that it is only accurate against armored vehicles if fired at extremely close ranges. While claimed to be effective against main battle tanks (except in frontal engagements) and lightly armored vehicles when first introduced, in 1972 the US Army stated in its revised anti-armor warfare manual that the M31 HEAT was only effective against light tanks and thin-skinned vehicles.[4]

Various US military manuals issued in 1972 still had sections on the M31, but by the end of the Vietnam War, both the US Army and US Marines had essentially phased out muzzle-launched rifle grenades, in favor of the M72 LAW disposable rocket in the anti-armor role and the M203 under-barrel grenade launcher in the squad fire-support role. In the 1977 revision of US military anti-armor warfare manuals, the M31 HEAT was no longer listed.[5]

External images
Drawings and Cutaways of M31 HEAT
Dimensions drawing of M31 HEAT rifle grenade
Cutaway drawing of M31 HEAT rifle grenade

References and notes

  1. ↑ US Army publication September 30, 1977 "FM-7 The Mechanized Infantry Platoon/Squad Section B-21" specification for M72A2 LAW variant which uses a warhead almost identical to the M31 HEAT
  2. ↑ Note - before the publication of FM-7 September 1977, various penetration specifications were given for the M72A2 and the M31 HEAT. Anywhere from 250mm to 305mm. In the mid 1970s the US Army decided in field test to truly determine the armour penetration under battlefield conditions again Russian tanks captured in 1973. The result was 200 mm (8 inches) the proceeding penetration specification is stated as it appears in FM-7 1977.
  3. ↑ Jane's Infantry Weapon's System 1976, page 452, Watts Publishing ISBN 0-531-03255-8
  4. ↑ FM 23-3 Tactics, Techniques and Concept of Antiarmor Warfare, page 14, published US Army August 1972
  5. ↑ One of the reasons was that, with the phase-out of the heavier 7.62mm assault rifles for the lighter 5.56mm assault rifles, they no longer had an infantry weapon that could launch a heavy antitank rifle grenade
This article is issued from Wikipedia - version of the 3/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.