Multi-mode optical fiber

A stripped multi-mode fiber

Multi-mode optical fiber is a type of optical fiber mostly used for communication over short distances, such as within a building or on a campus. Typical multimode links have data rates of 10 Mbit/s to 10 Gbit/s over link lengths of up to 600 meters (2000 feet).

Applications

The equipment used for communications over multi-mode optical fiber is less expensive than that for single-mode optical fiber.[1] Typical transmission speed and distance limits are 100 Mbit/s for distances up to 2 km (100BASE-FX), 1 Gbit/s up to 1000 m, and 10 Gbit/s up to 550 m.[2]

Because of its high capacity and reliability, multi-mode optical fiber generally is used for backbone applications in buildings. An increasing number of users are taking the benefits of fiber closer to the user by running fiber to the desktop or to the zone. Standards-compliant architectures such as Centralized Cabling and fiber to the telecom enclosure offer users the ability to leverage the distance capabilities of fiber by centralizing electronics in telecommunications rooms, rather than having active electronics on each floor.

Comparison with single-mode fiber

The main difference between multi-mode and single-mode optical fiber is that the former has much larger core diameter, typically 50–100 micrometers; much larger than the wavelength of the light carried in it. Because of the large core and also the possibility of large numerical aperture, multi-mode fiber has higher "light-gathering" capacity than single-mode fiber. In practical terms, the larger core size simplifies connections and also allows the use of lower-cost electronics such as light-emitting diodes (LEDs) and vertical-cavity surface-emitting lasers (VCSELs) which operate at the 850 nm and 1300 nm wavelength (single-mode fibers used in telecommunications typically operate at 1310 or 1550 nm [3]). However, compared to single-mode fibers, the multi-mode fiber bandwidth–distance product limit is lower. Because multi-mode fiber has a larger core-size than single-mode fiber, it supports more than one propagation mode; hence it is limited by modal dispersion, while single mode is not.

The LED light sources sometimes used with multi-mode fiber produce a range of wavelengths and these each propagate at different speeds. This chromatic dispersion is another limit to the useful length for multi-mode fiber optic cable. In contrast, the lasers used to drive single-mode fibers produce coherent light of a single wavelength. Due to the modal dispersion, multi-mode fiber has higher pulse spreading rates than single mode fiber, limiting multi-mode fiber’s information transmission capacity.

Single-mode fibers are often used in high-precision scientific research because restricting the light to only one propagation mode allows it to be focused to an intense, diffraction-limited spot.

Jacket color is sometimes used to distinguish multi-mode cables from single-mode ones. The standard TIA-598C recommends, for non-military applications, the use of a yellow jacket for single-mode fiber, and orange or aqua for multi-mode fiber, depending on type.[4] Some vendors use violet to distinguish higher performance OM4 communications fiber from other types.[5]

Types

Multi-mode fibers are described by their core and cladding diameters. Thus, 62.5/125 µm multi-mode fiber has a core size of 62.5 micrometres (µm) and a cladding diameter of 125 µm. The transition between the core and cladding can be sharp, which is called a step-index profile, or a gradual transition, which is called a graded-index profile. The two types have different dispersion characteristics and thus different effective propagation distance.[6] Multi-mode fibers may be constructed with either graded or step-index profile.[7]

In addition, multi-mode fibers are described using a system of classification determined by the ISO 11801 standard — OM1, OM2, and OM3 — which is based on the modal bandwidth of the multi-mode fiber. OM4 (defined in TIA-492-AAAD) was finalized in August 2009,[8] and was published by the end of 2009 by the TIA.[9] OM4 cable will support 125m links at 40 and 100 Gbit/s. The letters "OM" stand for optical multi-mode.

For many years 62.5/125 µm (OM1) and conventional 50/125 µm multi-mode fiber (OM2) were widely deployed in premises applications. These fibers easily support applications ranging from Ethernet (10 Mbit/s) to gigabit Ethernet (1 Gbit/s) and, because of their relatively large core size, were ideal for use with LED transmitters. Newer deployments often use laser-optimized 50/125 µm multi-mode fiber (OM3). Fibers that meet this designation provide sufficient bandwidth to support 10 Gigabit Ethernet up to 300 meters. Optical fiber manufacturers have greatly refined their manufacturing process since that standard was issued and cables can be made that support 10 GbE up to 400 meters. Laser optimized multi-mode fiber (LOMMF) is designed for use with 850 nm VCSELs.

The migration to LOMMF/OM3 has occurred as users upgrade to higher speed networks. LEDs have a maximum modulation rate of 622 Mbit/s because they can not be turned on/off fast enough to support higher bandwidth applications. VCSELs are capable of modulation over 10 Gbit/s and are used in many high speed networks.

Cables can sometimes be distinguished by jacket color: for 62.5/125 µm (OM1) and 50/125 µm (OM2), orange jackets are recommended, while Aqua is recommended for 50/125 µm "laser optimized" OM3 and OM4 fiber.[4]

VCSEL power profiles, along with variations in fiber uniformity, can cause modal dispersion which is measured by differential modal delay (DMD). Modal dispersion is caused by the different speeds of the individual modes in a light pulse. The net effect causes the light pulse to spread over distance, introducing intersymbol interference. The greater the length, the greater the modal dispersion. To combat modal dispersion, LOMMF is manufactured in a way that eliminates variations in the fiber which could affect the speed that a light pulse can travel. The refractive index profile is enhanced for VCSEL transmission and to prevent pulse spreading. As a result the fibers maintain signal integrity over longer distances, thereby maximizing the bandwidth.

Comparison

Minimum reach of Ethernet variants over multi-mode fiber
Category Minimum modal bandwidth
850 nm / 1300 nm[10]
Fast Ethernet 100BASE-FX 1 Gb (1000 Mb) Ethernet 1000BASE-SX 1 Gb (1000 Mb) Ethernet 1000BASE-LX 10 Gb Ethernet 10GBASE-SR 40 Gb Ethernet 40GBASE-SR4 100 Gb Ethernet 100GBASE-SR10
FDDI (62.5/125) 160 / 500 MHz·km 2000 m[11] 220 m[12] 550 m[11] (mode-conditioning patch cord required)[13] 26 m[14] Not supported Not supported
OM1 (62.5/125) 200 / 500 MHz·km 275 m[15] 33 m[11] Not supported Not supported
OM2 (50/125) 500 / 500 MHz·km 550 m[2] 82 m[2] Not supported Not supported
OM3 (50/125) *Laser Optimized* 1500 / 2000 MHz·km 300 m[11] 100 m[2]

(330 m QSFP+ eSR4[16])

100 m[2]
OM4 (50/125) *Laser Optimized* 3500 / 4700 MHz·km 400 m[17] 150 m[2]

(550 m QSFP+ eSR4[16])

150 m[2]

Encircled flux

The new IEC 61280-4-1 standard called encircled flux specifies the injection size, to make sure the core is not over-filled or under-filled.

See also

References

  1. Telecommunications Industry Association. "Multimode Fiber for Enterprise Networks". Retrieved Jun 4, 2008.
  2. 1 2 3 4 5 6 7 Furukawa Electric North America. "OM4 - The next generation of multimode fiber" (pdf). Retrieved May 16, 2012.
  3. ARC Electronics (Oct 1, 2007). "Fiber Optic Cable Tutorial". Retrieved March 4, 2015.
  4. 1 2 "Fiber optic cable color codes". Tech Topics. The Fiber Optic Association. Retrieved Sep 17, 2009.
  5. Crawford, Dwayne (Sep 11, 2013). "Who is Erika Violet and what is she doing in my data center?". Tech Topics. Belden. Retrieved Feb 12, 2014.
  6. British FibreOptic Industry Association. "Optical Fibers Explained" (PDF). Retrieved Apr 9, 2011.
  7. "Fiber Optics Overview". Retrieved 2012-11-23.
  8. "Meeting Report #14" (PDF). Telecommunications Industry Association.
  9. Kish, Paul (2010-01-01). "Next generation fiber arrives". # Cabling Networking Systems. Business Information Group.
  10. OFL Over-Filled Launch for 850 nm / EMB Effective Modal Bandwidth for 1310 nm
  11. 1 2 3 4 Hewlett-Packard Development Company, L.P. (2007). "100BASE-FX Technical Brief" (pdf). Retrieved Nov 20, 2012.
  12. IEEE 802.3-2012 Clause 38.3
  13. Cisco Systems, Inc (2009). "Cisco Mode-Conditioning Patch Cord Installation Note". Retrieved Feb 20, 2015.
  14. "Cisco 10GBASE X2 Modules Data Sheet". Cisco. Retrieved June 23, 2015.
  15. IEEE 802.3-2012 Clause 38.3
  16. 1 2 "40G Extended Reach with Corning Cable Systems OM3/OM4 Connectivity with the Avago 40G QSFP+ eSR4 Transceiver" (pdf). Corning. 2013. Retrieved 14 August 2013.
  17. "IEEE 802.3". Retrieved 31 October 2014.

External links

This article is issued from Wikipedia - version of the 9/6/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.