Overlap–save method

Overlap–save is the traditional name for an efficient way to evaluate the discrete convolution between a very long signal $x[n]$ and a finite impulse response (FIR) filter $h[n]$ :

$y[n]=x[n]*h[n]\ {\stackrel {{\mathrm {def}}}{=}}\ \sum _{{m=-\infty }}^{{\infty }}h[m]\cdot x[n-m]=\sum _{{m=1}}^{{M}}h[m]\cdot x[n-m],\,$

(Eq.1)

where h[m]=0 for m outside the region [1, M].

A sequence of 4 plots depicts one cycle of the Overlap-save convolution algorithm. The 1st plot is a long sequence of data to be processed with a lowpass FIR filter. The 2nd plot is one segment of the data to be processed in piecewise fashion. The 3rd plot is the filtered segment, with the usable portion colored red. The 4th plot shows the filtered segment appended to the output stream. The FIR filter is a boxcar lowpass with M=16 samples, the length of the segments is L=100 samples and the overlap is 15 samples.

The concept is to compute short segments of y[n] of an arbitrary length L, and concatenate the segments together. Consider a segment that begins at n = kL + M, for any integer k, and define:

x_{k}[n]\ {\stackrel {{\mathrm {def}}}{=}}{\begin{cases}x[n+kL]&1\leq n\leq L+M-1\\0&{\textrm {otherwise}}.\end{cases}}

y_{k}[n]\ {\stackrel {{\mathrm {def}}}{=}}\ x_{k}[n]*h[n]\,

Then, for kL + M ≤ n ≤ kL + L + M − 1, and equivalently M ≤ n − kL ≤ L + M − 1, we can write:

{\begin{aligned}y[n]=\sum _{{m=1}}^{{M}}h[m]\cdot x_{k}[n-kL-m]&=x_{k}[n-kL]*h[n]\\&{\stackrel {{\mathrm {def}}}{=}}\ y_{k}[n-kL].\end{aligned}}

The task is thereby reduced to computing y_k[n], for M ≤ n ≤ L + M − 1. The process described above is illustrated in the accompanying figure.

Now note that if we periodically extend x_k[n] with period N ≥ L + M − 1, according to:

x_{{k,N}}[n]\ {\stackrel {{\mathrm {def}}}{=}}\ \sum _{{\ell =-\infty }}^{{\infty }}x_{k}[n-\ell N],

the convolutions $(x_{{k,N}})*h\,$ and $x_{k}*h\,$ are equivalent in the region M ≤ n ≤ L + M − 1. So it is sufficient to compute the N-point circular (or cyclic) convolution of $x_{k}[n]\,$ with $h[n]\,$ in the region [1, N]. The subregion [M, L + M − 1] is appended to the output stream, and the other values are discarded.

The advantage is that the circular convolution can be computed very efficiently as follows, according to the circular convolution theorem:

y_{k}[n]=\scriptstyle {\text{DFT}}^{{-1}}\displaystyle (\ \scriptstyle {\text{DFT}}\displaystyle (x_{k}[n])\cdot \scriptstyle {\text{DFT}}\displaystyle (h[n])\ ),

where:

DFT and DFT⁻¹ refer to the Discrete Fourier transform and inverse Discrete Fourier transform, respectively, evaluated over N discrete points, and
N is customarily chosen to be an integer power-of-2, which optimizes the efficiency of the FFT algorithm.
Optimal N is in the range [4M, 8M].
Unlike the third graph in the figure above, depicting separate leading and trailing edge-effects, this method causes them to be overlapped and added. So they are discarded together.

Pseudocode


 (Overlap–save algorithm for linear convolution)
 h = FIR_impulse_response
 M = length(h)
 overlap = M-1
 N = 4*overlap    (or a nearby power-of-2)
 step_size = N-overlap
 H = DFT(h, N)
 position = 0
 while position+N <= length(x)
     yt = IDFT( DFT( x(1+position : N+position), N ) * H, N )
     y(1+position : step_size+position) = yt(M : N)    #discard M-1 y-values
     position = position + step_size
 end

Efficiency

When the DFT and its inverse is implemented by the FFT algorithm, the pseudocode above requires about N log₂(N) + N complex multiplications for the FFT, product of arrays, and IFFT.^{[note 1]} Each iteration produces N-M+1 output samples, so the number of complex multiplications per output sample is about:

${\frac {N\log _{2}(N)+N}{N-M+1}}.\,$

(Eq.2)

For example, when M=201 and N=1024, Eq.2 equals 13.67, whereas direct evaluation of Eq.1 would require up to 201 complex multiplications per output sample, the worst case being when both x and h are complex-valued. Also note that for any given M, Eq.2 has a minimum with respect to N. It diverges for both small and large block sizes.

Overlap–discard

Overlap–discard^[1] and Overlap–scrap^[2] are less commonly used labels for the same method described here. However, these labels are actually better (than overlap–save) to distinguish from overlap–add, because both methods "save", but only one discards. "Save" merely refers to the fact that M − 1 input (or output) samples from segment k are needed to process segment k + 1.

Extending overlap–save

The overlap-save algorithm may be extended to include other common operations of a system:^{[note 2]}^[3]

additional channels can be processed more cheaply than the first by reusing the forward FFT
sampling rates can be changed by using different sized forward and inverse FFTs
frequency translation (mixing) can be accomplished by rearranging frequency bins

Notes

↑ Cooley-Tukey FFT algorithm for N=2^k needs (N/2) log₂(N) - see FFT - Definition and speed
↑ Carlin et al. 1999, p 31, col 20.

References

↑ Harris, F.J. (1987). "Time domain signal processing with the DFT". Handbook of Digital Signal Processing, D.F.Elliot, ed., San Diego: Academic Press. pp 633–699. ISBN 0122370759.
↑ Frerking, Marvin (1994). Digital Signal Processing in Communication Systems. New York: Van Nostrand Reinhold. ISBN 0442016166.
↑ Borgerding, Mark (2006), "Turning Overlap-Save into a Multiband Mixing, Downsampling Filter Bank" (PDF), IEEE Signal Processing Magazine (March 2006): 158–161

US patent 6898235, Carlin, Joe; Terry Collins & Peter Hays et al., "Wideband communication intercept and direction finding device using hyperchannelization", published 1999, issued 2005