Piston motion equations

The motion of a non-offset piston connected to a crank through a connecting rod (as would be found in internal combustion engines), can be expressed through several mathematical equations. This article shows how these motion equations are derived, and shows an example graph.

Crankshaft geometry

Diagram showing geometric layout of piston pin, crank pin and crank center

Definitions

l = rod length (distance between piston pin and crank pin)
r = crank radius (distance between crank pin and crank center, i.e. half stroke)
A = crank angle (from cylinder bore centerline at TDC)
x = piston pin position (upward from crank center along cylinder bore centerline)
v = piston pin velocity (upward from crank center along cylinder bore centerline)
a = piston pin acceleration (upward from crank center along cylinder bore centerline)
ω = crank angular velocity in rad/s

Angular velocity

The crankshaft angular velocity is related to the engine revolutions per minute (RPM):

Triangle relation

As shown in the diagram, the crank pin, crank center and piston pin form triangle NOP.
By the cosine law it is seen that:

Equations with respect to angular position (Angle Domain)

The equations that follow describe the reciprocating motion of the piston with respect to crank angle.
Example graphs of these equations are shown below.

Position

Position with respect to crank angle (by rearranging the triangle relation):

Velocity

Velocity with respect to crank angle (take first derivative, using the chain rule):

Acceleration

Acceleration with respect to crank angle (take second derivative, using the chain rule and the quotient rule):

Equations with respect to time (Time Domain)

Angular velocity derivatives

If angular velocity is constant, then

and the following relations apply:

Converting from Angle Domain to Time Domain

The equations that follow describe the reciprocating motion of the piston with respect to time.

If time domain is required instead of angle domain, first replace A with ωt in the equations, and then scale for angular velocity as follows:

Position

Position with respect to time is simply the x' equation with angle A replaced with ωt:

Velocity

Velocity with respect to time (using the chain rule):

Acceleration

Acceleration with respect to time (using the chain rule and product rule, and the angular velocity derivatives):

Scaling for angular velocity

You can see that x is unscaled, x' is scaled by ω, and x" is scaled by ω².
To convert x' from velocity vs angle [inch/rad] to velocity vs time [inch/s] multiply x' by ω [rad/s].
To convert x" from acceleration vs angle [inch/rad²] to acceleration vs time [inch/s²] multiply x" by ω² [rad²/s²].
Note that dimensional analysis shows that the units are consistent.

Velocity maxima/minima

Acceleration zero crossings

The velocity maxima and minima do not occur at crank angles (A) of plus or minus 90°.
The velocity maxima and minima occur at crank angles that depend on rod length (l) and half stroke (r),
and correspond to the crank angles where the acceleration is zero (crossing the horizontal axis).

Crank-Rod angle not right angled

The velocity maxima and minima do not necessarily occur when the crank makes a right angle with the rod.
Counter-examples exist to disprove the idea that velocity maxima/minima occur when crank-rod angle is right angled.

Example

For rod length 6" and crank radius 2", numerically solving the acceleration zero-crossings finds the velocity maxima/minima to be at crank angles of ±73.17615°.
Then, using the triangle sine law, it is found that the crank-rod angle is 88.21738° and the rod-vertical angle is 18.60647°.
Clearly, in this example, the angle between the crank and the rod is not a right angle.

(Sanity check, summing the angles of the triangle 88.21738° + 18.60647° + 73.17615° gives 180.00000°)

A single counter-example is sufficient to disprove the statement "velocity maxima/minima occur when crank makes a right angle with rod".

Example graph of piston motion

The graph shows x, x', x" with respect to crank angle for various half strokes, where L = rod length (l) and R = half stroke (r):

The vertical axis units are inches for position, [inches/rad] for velocity, [inches/rad²] for acceleration.
The horizontal axis units are crank angle degrees.

Pistons motion animation with same rod length and crank radius values in graph above :

See also

References

    Further reading

    External links

    This article is issued from Wikipedia - version of the 11/30/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.