Sound power

Sound measurements
Characteristic
Symbols
 Sound pressure  p, SPL
 Particle velocity  v, SVL
 Particle displacement  δ
 Sound intensity  I, SIL
 Sound power  P, SWL
 Sound energy  W
 Sound energy density  w
 Sound exposure  E, SEL
 Acoustic impedance  Z
 Speed of sound  c
 Audio frequency  AF
 Transmission loss  TL

Sound power or acoustic power is the rate at which sound energy is emitted, reflected, transmitted or received, per unit time.[1] The SI unit of sound power is the watt (W).[1] It is the power of the sound force on a surface of the medium of propagation of the sound wave. For a sound source, unlike sound pressure, sound power is neither room-dependent nor distance-dependent. Sound pressure is a measurement at a point in space near the source, while the sound power of a source is the total power emitted by that source in all directions. Sound power passing through an area is sometimes called sound flux or acoustic flux through that area.

Mathematical definition

Sound power, denoted P, is defined by[2]

where

In a medium, the sound power is given by

where

For example, a sound at SPL = 85 dB or p = 0.356 Pa in air (ρ = 1.2 kg·m−3 and c = 343 m·s−1) through a surface of area A = 1 m2 normal to the direction of propagation (θ = 0 °) has a sound energy flux P = 0.3 mW.

This is the parameter one would be interested in when converting noise back into usable energy, along with any losses in the capturing device.

Table of selected sound sources

Maximum sound power level (LWA) related to a portable air compressor.

Here is a table of some examples, from an on-line source.[3] The top three or four lines seem questionable. A 150-dB source should be audible 100 times as far away as a 110-dB source, and a 200-dB source 10 000 times further than a 120-dB source. This would imply that a turbofan aircraft at take-off would be audible 100 times further than a rock concert, and a Saturn V 10 000 times further than heavy thunder. However this simple analysis does not account for the effect of atmospheric absorption effects and how they change with frequency.

Situation and
sound source
Sound power
(W)
Sound power level
(dB ref 10−12 W)
Saturn V rocket 100,000,000 200
Project Artemis Sonar 1,000,000
Turbojet engine 100,000 170
Turbofan aircraft at take-off 1,000 150
Turboprop aircraft at take-off 100 140
Machine gun
Large pipe organ
10 130
Symphony orchestra
Heavy thunder
Sonic boom
1 120
Rock concert
Chain saw
Accelerating motorcycle
0.1 110
Lawn mower
Car at highway speed
Subway steel wheels
0.01 100
Large diesel vehicle 0.001 90
a loud Alarm clock 0.0001 80
a relatively quiet Vacuum cleaner 10−5 70
Hair dryer 10−6 60
Radio or TV 10−7 50
Refrigerator
low voice
10−8 40
Quiet conversation 10−9 30
Whisper of one person
Wristwatch ticking
10−10 20
Human breath of one person 10−11 10
Reference value 10−12 0

Relationships with other quantities

Sound power is related to sound intensity:

where

Sound power is related sound energy density:

where

Sound power level

For other uses, see Sound level.

Sound power level (SWL) or acoustic power level is a logarithmic measure of the power of a sound relative to a reference value.
Sound power level, denoted LW and measured in dB, is defined by[4]

where

The commonly used reference sound power in air is[5]

The proper notations for sound power level using this reference are LW/(1 pW) or LW (re 1 pW), but the suffix notations dB SWL, dB(SWL), dBSWL, or dBSWL are very common, even if they are not accepted by the SI.[6]

The reference sound power P0 is defined as the sound power with the reference sound intensity I0 = 1 pW/m2 passing through a surface of area A0 = 1 m2:

hence the reference value P0 = 1 pW.

Relationship with sound pressure level

The generic calculation of sound power from sound pressure is as follows:

where: defines the area of a surface that wholly encompasses the source. This surface may be any shape, but it must fully enclose the source.

In the case of a sound source located in free field positioned over a reflecting plane (i.e. the ground), in air at ambient temperature, the sound power level at distance r from the sound source is approximately related to sound pressure level (SPL) by[7]

where

Derivation of this equation:

For a progressive spherical wave,

(the surface area of sphere)

where z0 is the characteristic specific acoustic impedance.

Consequently,

and since by definition I0 = p02/z0, where p0 = 20 μPa is the reference sound pressure,

The sound power estimated practically does not depend on distance. The sound pressure used in the calculation may be affected by distance due to viscous effects in the propagation of sound unless this is accounted for.

References

  1. 1 2 Ronald J. Baken, Robert F. Orlikoff (2000). Clinical Measurement of Speech and Voice. Cengage Learning. p. 94. ISBN 9781565938694.
  2. Landau & Lifshitz, "Fluid Mechanics", Course of Theoretical Physics, Vol. 6
  3. "Sound Power". The Engineering Toolbox. Retrieved 28 November 2013.
  4. "Letter symbols to be used in electrical technology – Part 3: Logarithmic and related quantities, and their units", IEC 60027-3 Ed. 3.0, International Electrotechnical Commission, 19 July 2002.
  5. Ross Roeser, Michael Valente, Audiology: Diagnosis (Thieme 2007), p. 240.
  6. Thompson, A. and Taylor, B. N. sec 8.7, "Logarithmic quantities and units: level, neper, bel", Guide for the Use of the International System of Units (SI) 2008 Edition, NIST Special Publication 811, 2nd printing (November 2008), SP811 PDF
  7. Chadderton, David V. Building services engineering, pp. 301, 306, 309, 322. Taylor & Francis, 2004. ISBN 0-415-31535-2
This article is issued from Wikipedia - version of the 11/5/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.