Statcoulomb

The statcoulomb (statC) or franklin (Fr) or electrostatic unit of charge (esu) is the physical unit for electrical charge used in the esu-cgs (centimetre-gram-second system of units) and Gaussian units. It is a derived unit given by

1 statC =dyn^1/2 cm= cm^3/2 g^1/2 s⁻¹.

It can be converted using

1 newton = 10⁵ dyne

1 cm= 10^(-2)m

The SI system of units uses the coulomb (C) instead. The conversion between C and statC is different in different contexts. The most common contexts are:

• For electric charge:

  1 C ↔ 2997924580 statC ≈ 3.00×10⁹ statC

  ⇒ 1 statC ↔ ~3.33564×10⁻¹⁰ C.

• For electric flux (Φ_D):

  1 C ↔ 4π×2997924580 statC ≈3.77×10¹⁰ statC

  ⇒ 1 statC ↔ ~2.65×10⁻¹¹ C.

The symbol "↔" is used instead of "=" because the two sides are not necessarily interchangeable, as discussed below. The number 2997924580 is 10 times the value of the speed of light expressed in meters/second, and the conversions are exact except where indicated. The second context implies that the SI and cgs units for an electric displacement field (D) are related by:

1 C/m² ↔ 4π×2997924580×10⁻⁴ statC/cm² ≈ 3.77×10⁶ statC/cm²

⇒ 1 statC/cm² ↔ ~2.65×10⁻⁷ C/m²

due to the relation between the metre and the centimetre. The coulomb is an extremely large charge rarely encountered in electrostatics, while the statcoulomb is closer to everyday charges.

Definition and relation to cgs base units

The statcoulomb is defined as follows: if two stationary objects each carry a charge of 1 statC and are 1 cm apart, they will electrically repel each other with a force of 1 dyne. This repulsion is governed by Coulomb's law, which in the Gaussian-cgs system states:

$F={\frac {q_{1}q_{2}}{r^{2}}}$

where F is the force, q₁ and q₂ are the two charges, and r is the distance between the charges. Performing dimensional analysis on Coulomb's law, the dimension of electrical charge in cgs must be [mass]^1/2 [length]^3/2 [time]⁻¹. (This statement is not true in SI units; see below.) We can be more specific in light of the definition above: Plugging in F = 1 dyn, q₁ = q₂ = 1 statC, and r = 1 cm, we get:

1 statC = g^1/2 cm^3/2 s⁻¹

as expected.

Dimensional relation between Statcoulomb and Coulomb

General incompatibility

Coulomb's law in cgs-Gaussian unit system and SI are respectively:

$F={\frac {q_{1}q_{2}}{r^{2}}}$ (cgs-Gaussian)

$F={\frac {q_{1}q_{2}}{4\pi \epsilon _{0}r^{2}}}$ (SI)

Since ε₀, the vacuum permittivity, is not dimensionless, the coulomb (the SI unit of charge) is not dimensionally equivalent to [mass]^1/2 [length]^3/2 [time]⁻¹, unlike the statcoulomb. In fact, it is impossible to express the coulomb in terms of mass, length, and time alone.

Consequently, a conversion equation like "1 C = N statC" can be misleading: the units on the two sides are not consistent. One cannot freely switch between coulombs and statcoulombs within a formula or equation, as one would freely switch between centimeters and meters. One can, however, find a correspondence between coulombs and statcoulombs in different contexts. As described below, "1 C corresponds to 3.00×10⁹ statC" when describing the charge of objects. In other words, if a physical object has a charge of 1 C, it also has a charge of 3.00×10⁹ statC. Likewise, "1 C corresponds to 3.77×10¹⁰ statC" when describing an electric displacement field flux.

As a unit of charge

The statcoulomb is defined as follows: If two stationary objects each carry a charge of 1 statC and are 1 cm apart, they will electrically repel each other with a force of 1 dyne. From this definition, it is straightforward to find an equivalent charge in SI coulombs. Using the SI equation

$F={\frac {q_{1}q_{2}}{4\pi \epsilon _{0}r^{2}}}$ (SI),

and plugging in F = 1 dyn = 10⁻⁵ N, and r = 1 cm = 10⁻² m, and then solving for q = q₁ = q₂, the result is q = (1/2997924580)C ≈ 3.34×10⁻¹⁰ C. Therefore, an object with a charge of 1 statC has a charge of 3.34×10⁻¹⁰ C.

This can also be expressed by the following conversion, which is fully dimensionally consistent, and often useful for switching between SI and cgs formulae:

$1\;{\mathrm {C}}/{\sqrt {4\pi \epsilon _{0}}}=2997924580\;{\mathrm {statC}}$

As a unit of electric displacement field or flux

An electric flux (specifically, a flux of the electric displacement field D) has units of charge: statC in cgs and coulombs in SI. The conversion factor can be derived from Gauss's law:

$\Phi _{D}=4\pi Q$ (cgs)

$\Phi _{D}=Q$ (SI)

where

$\Phi _{D}\equiv \int _{S}{\mathbf {D}}\cdot {\mathrm {d}}{\mathbf {A}}$

Therefore, the conversion factor for flux is 4π different from the conversion factor for charge:

$1\;{\mathrm {C}}{\text{ corresponds to }}3.7673\times 10^{{10}}\;{\mathrm {statC}}$ (as unit of Φ_D).

The dimensionally consistent version is:

$1\;{\mathrm {C}}{\sqrt {4\pi /\epsilon _{0}}}=3.7673\times 10^{{10}}\;{\mathrm {statC}}$ (as unit of Φ_D).