A stationary engine is an engine whose framework does not move, used to drive a piece of immobile equipment, such as a pump, generator, or mill or factory machinery. The term usually refers to large immobile reciprocating engines, principally stationary steam engines and, to some extent, stationary internal combustion engines. Other large immobile power sources, such as steam turbines, gas turbines, and large electric motors, are categorized separately.
Stationary engines were once widespread in the era when each factory or mill generated its own power, and power transmission was mechanical (via line shafts, belts, gear trains, and clutches). Applications for stationary engines have declined since electrification has become widespread; most industrial uses today draw electricity from an electrical grid and distribute it to various individual electric motors instead.
Engines that operate in one place, but can be moved to another place for later operation, are called portable engines. Although stationary engines and portable engines are both "stationary" (not moving) while running, preferred usage (for clarity's sake) reserves the term "stationary engine" to the permanently immobile type, and "portable engine" to the mobile type.
Types of stationary engine
Lead, tin and copper mines
Cotton, Woollen and Worsted Mills
Before mains electricity and the formation of nationwide power grids, stationary engines were widely used for small-scale electricity generation. Whilst large power stations in cities used steam turbines or high-speed reciprocating steam engines, in rural areas petrol/gasoline, paraffin/kerosene or fuel oil powered internal combustion engines were cheaper to buy, install and operate, since they could be started and stopped quickly to meet demand, left running unattended for long periods of time and did not require a large dedicated engineering staff to operate and maintain. Due to their simplicity and economy, hot bulb engines were popular for high-power applications until the diesel engine took their place from the 1920s. Smaller units were generally powered by spark-ignition engines, which were cheaper to buy and required less space to install.
Most engines of the late-19th and early-20th centuries ran at speeds too low to drive a dynamo or alternator directly. As with other equipment, the generator was driven off the engine's flywheel by a broad flat belt. The pulley on the generator was much smaller than the flywheel, providing the required 'gearing up' effect. Later spark-ignition engines developed from the 1920s could be directly coupled.
Up to the 1930s most rural houses in Europe and North America needed their own generating equipment if electric light was fitted. Engines would often be installed in a dedicated 'engine house', which was usually an outbuilding separate from the main house to reduce the interference from the engine noise. The engine house would contain the engine, the generator, the necessary switchgear and fuses, as well as the engine's fuel supply and usually a dedicated workshop space with equipment to service and repair the engine. Wealthy households could afford to employ a dedicated engineer to maintain the equipment, but as the demand for electricity spread to smaller homes, manufacturers produced engines that required less maintenance and that did not need specialist training to operate.
Such generator sets were also used in industrial complexes and public buildings- anywhere where electricity was required but mains electricity was not available.
Most countries in the Western world completed large-scale rural electrification in the years following World War II, making individual generating plants obsolete for front-line use. However, even in countries with a reliable mains supply, many buildings are still fitted with modern diesel generators for emergency use, such as hospitals and pumping stations. This network of generators often forms a crucial part of the national electricity system's strategy for coping with periods of high demand.
The development of water supply and sewage removal systems required the provision of many pumping stations. In these, some form of stationary engine (steam-powered for earlier installations) is used to drive one or more pumps, although electric motors are more conventionally used nowadays.
For canals, a distinct area of application concerned the powering of boat lifts and inclined planes. Where possible these would be arranged to utilise water and gravity in a balanced system, but in some cases additional power input was required from a stationary engine for the system to work. The vast majority of these were constructed (and in many cases, demolished again) before steam engines were supplanted by internal combustion alternatives.
Cable haulage railways
Industrial railways in quarries and mines made use of cable railways based on the inclined plane idea, and certain early passenger railways in the UK were planned with lengths of cable-haulage to overcome severe gradients.
For the first proper railway, the Liverpool and Manchester of 1830, it was not clear whether locomotive traction would work, and the railway was designed with steep 1 in 100 gradients concentrated on either side of Rainhill, just in case. Had cable haulage been necessary, then inconvenient and time-consuming shunting would obviously have been required to attach and detach the cables. Fortunately, the Rainhill gradients proved not to be a problem, and in the event, locomotive traction was determined to be a new technology with great potential for further development.
The steeper 1 in 50 grades from Liverpool down to the docks were operated by cable traction for several decades until locomotives improved. Cable haulage continued to be used where gradients were even steeper.
Cable haulage did prove viable where the gradients were exceptionally steep, such as the 1 in 8 gradients of the Cromford and High Peak Railway opened in 1830. Cable railways generally have two tracks with loaded wagons on one track partially balanced by empty wagons on the other, to minimise fuel costs for the stationary engine. Various kinds of rack railway were developed to overcome the lack of friction of conventional locomotives on steep gradients.
These early installations of stationary engines would all have been steam-powered initially.
Some manufacturers of stationary engines
- Amanco USA
- Blackstone & Co UK c.1882 - 1936
- Briggs & Stratton USA
- Charter Gas Engine Company c.1883-1920s
- Deere & Company / John Deere USA
- Electro-Motive USA
- Emerson-Brantingham USA
- Fairbanks-Morse USA
- Fuller and Johnson
- Hercules Gas Engine Company 1912-1930s
- Hercules Motors Corporation 1915-1967, 1976-
- Richard Hornsby & Sons UK
- International Harvester USA
- Jacobson Machine Manufacturing Company
- Kohler Company USA
- Lister Petter UK
- Malkotsis Greece
- National Gas Engine Company UK
- New Holland Machine Company USA
- Olds Gasoline Engine Works (Pliny Olds, sons Wallace and Ransom) (1890s-1910)
- Otto Gas Engine Works
- Palmer Brothers
- Rider-Ericsson Engine Company
- Stover Manufacturing and Engine Company
- Van Duzen Gas and Gasoline Engine Company c.1891-1898
- Waterloo Gasoline Engine Company USA
- Witte Engine Works
Preserved stationary engines
In the UK there are few museums where visitors can see stationary engines in operation. Many museums have one or more engines but only a few specialise in the internal combustion stationary engines. Among these are the Internal Fire - Museum of Power, in Wales, and the Anson Engine Museum in Cheshire. The Amberley Working Museum in West Sussex also has a number of engines, as does Kew Bridge Steam Museum in London.
Many steam rallies, like the Great Dorset Steam Fair, include an exhibit section for internal combustion stationary engines. These engines have been restored by private individuals and often are exhibited in operation, powering water pumps, electric generators, hand tools, and the like.
|Wikimedia Commons has media related to Stationary engines.|
- Antique Stationary Engines
- Internal Fire Museum of Power in Wales
- Anson Engine Museum in Cheshire
- Stationary engine website
- Stationary engines in South Africa
- Harry's Old Engine Home Page