Teletype Model 33

A Teletype Model 33 ASR teleprinter, with punched tape reader and punch, usable as a computer terminal

The Teletype Model 33 is an electromechanical teleprinter designed for light-duty office. It is less rugged and less expensive than earlier Teletype machines. The Teletype Corporation introduced the Model 33 as a commercial product in 1963[1] after being originally designed for the US Navy.[2] There are three versions of the Model 33:

The Model 33 was one of the first products to employ the then new ASCII code. A companion Model 32 used the more established five-level Baudot code. Because of its low price and ASCII-compatibility, the Model 33 was widely used with early minicomputers.

History

Teletype Corporation's Model 33 terminal, introduced in 1963, is one of the most popular terminals in the data-communications industry. Over a half-million Model 32s and 33s were made by 1975, and the 500,000th was plated with gold and placed on special exhibit.[3] Another 100,000 were made in the next 18 months, and Serial Number 600,000, manufactured in 1976, the United States Bicentennial year, was painted red-white-and-blue and shown around the United States during the last part of that year and the year after.[4]

A Model 33 ASR in use in 1978

A Model 33 cost about $700, much less than other teleprinters and computer terminals at the time, such as the Friden Flexowriter and the IBM 1050. Early video terminals, such as the Tektronix 4010, did not become available until 1970 and cost around $10,000. However the introduction of integrated circuits and semiconductor memory later that decade allowed the price of cathode-ray-tube-based terminals to fall below the price of a Teletype. Teletype machines were gradually replaced in new installations by dot-matrix printers and CRT-based terminals in the mid to late 1970s. Basic CRT-based terminals which could only print lines and scroll them are often called glass teletypes to distinguish them from more sophisticated devices.

Teletype Corporation discontinued Model 33 production in 1981.[5]

Model 33 ASR vis-à-vis ASR-33

While the manufacturer called the Model 33 teleprinter with a tape punch and tape reader a Model 33 ASR, many users, specifically computer users, called this equipment an ASR-33. The earliest known source for this Teletype Corporation equipment naming discrepancy comes from Digital Equipment Corporation documentation[6] where the September 1963 PDP-4 Brochure calls the Teletype Model 28 KSR a "KSR-28" in the paragraph titled "Printer-Keyboard and Control Type 65". This naming discrepancy continued from the Teletype Model 28 to other Teletype equipment in later DEC documentation. For example, Digital Equipment Corporation's PDP-15 Price List from April 1970 lists a number of Teletype Corporation teletypewriters using this alternate naming convention.[7]

This alternate naming convention was continued as other computer manufacturers published their documentation. For example, Micro Instrumentation and Telemetry Systems sold the Teletype Model 33 ASR as "Teletype ASR-33".

Technical information

A Teletype Model 33 ASR teleprinter keyboard with punched tape reader and punch. The left-front unit is the tape reader with its three-position START/STOP/FREE lever in the STOP position. A less-common tape reader had a four-position START/AUTO/STOP/FREE lever. In the AUTO position it could be commanded on and off remotely. The tape punch is the unit directly behind the reader. As it exits the machine, the tape passes under a triangular lip that allows the tape to be easily torn by lifting against the sharp edge of the lip.

The design objective for the Model 33 was a machine that would fit into a small office space, match with other office equipment of the time and operate up to two hours per day on average. Since this machine was designed for light duty use, adjustments that Teletype made in previous teleprinters by turning screws were made by bending metal bars and levers. Many Model 33 parts were not heat treated and hardened. However, the base was die cast, but self-tapping screws were used, along with parts that snapped together without bolting. In another cost saving measure, the paper tape equipment was dependent on the keyboard and page printer mechanisms. Earlier Teletype machine designs, such as the Model 28 ASR, allowed the user to operate the keyboard to punch tape while transmitting a previously punched tape and to punch a tape while printing something else. Independent use of the paper tape punch and reader is not possible with the Model 33 ASR.[8]

The Model 33 used the seven-bit upper-case only ASCII code, also known as CCITT International Telegraphic Alphabet No. 5, with one (even) parity bit and two stop bits. The Model 33 is usually geared to run at maximum speed ten characters per second speed, i.e., 100 words per minute (wpm), but other speeds are available: 60 wpm, 66 wpm, 68.2 wpm, and 75 wpm.[9] There were also many typewheel options. The Teletype Parts Bulletin[10] lists sixty-nine available Model 33 typewheel options.

The Teletype Model 33 contained an answer-back mechanism that was generally used in dial-up networks such as the TWX network. At the beginning of the message, the sending machine could transmit an enquiry character or WRU (Who aRe yoU) code, and the recipient machine would automatically initiate a response which was encoded in a rotating drum that could be programmed by breaking off tabs.[11] The answer-back drum in the recipient machine would rotate and send an unambiguous identifying code to the sender, so the sender could verify connection to the correct recipient. The WRU code could also be sent at the end of the message. A correct response would confirm that the connection had remained unbroken during the message transmission. Finally, the sending machine operator would press the disconnect button. Note that the receiving machine did not need operator intervention. Since messages were often sent across multiple time zones to their destination, it was common to send a message to a location where the receiving machine was operating in an office that was closed and unmanned.

The Teletype Model 33, including the stand, is 34 inches (86 cm) high, 22 inches (56 cm) wide and 18.5 inches (47 cm) deep, not including the paper holder. The Teletype Model 33 weighs 75 pounds (34 kg) on the stand, including paper. This machine requires less than 4 amperes at 115 VAC 60 Hz. The recommended operating environment is a temperature of 40 °F to 110 °F (4 °C to 43 °C), a relative humidity of 2 to 95 percent and an altitude of 0 to 10,000 feet (3050 m). The printing paper is an 8.44 inch by 4.5 inch diameter roll and the paper tape is a one inch by 1000 foot roll. Ribbons are 0.5 inch wide by 60 yards long with plastic spools and eyelets for proper ribbon reverse operation.

Interface

The Model 33 could accommodate an internal modem with an optional acoustic coupler to the right of the keyboard. This was replaced by a blank panel on units operating on a current loop. There were different kinds of Model 33 Call Control Units (CCUs) that included Rotary Dial, Touch-Tone, Card Dialing and Computer Control Private Line variations. In the 1960s and early 1970s minicomputers typically had a 20mA current loop interface for connection to a Teletype machine used as a console terminal and paper tape program loader. As the price of electronic terminals dropped in the late 1970s, the current loop was gradually replaced by an RS-232 interface.

A Model 32 used for Telex service. Note the three row keyboard and narrower, five-level paper tape.
A Model 35 ASR, at the Living Computer Museum in Seattle

The Model 32 line used the same mechanism and looked identical, except for having a three-row keyboard and, on the ASR model, a five-level paper tape reader and punch, both appropriate for Baudot code.

Teletype also introduced a more expensive ASCII Model 35 for heavy duty use, whose printer mechanism was based on the older, rugged Model 28. The basic Model 35 was mounted in a light gray console that matched the width of the Model 33, while the Model 35 ASR with eight-level mechanical tape punch and reader was installed in a console about twice as wide. The tape reader was mounted separately from the printer-punch mechanism on the left side of the console and behind it was a tray for storing a manual, sheets of paper, or other miscellanea. To the right of the keyboard was a panel that could optionally house a rotary dial or Touch-Tone pushbuttons for dialing a connection to a network via telephone lines. The printer cover in later units also featured sound deadening materials, making the Model 35 somewhat quieter than the Model 33 while printing and punching paper tapes. All versions of the Model 35 had a copy holder on the printer cover, making it more convenient for the operator when transcribing written material.

More expensive Teletype systems used photo readers that used light sensors to detect the presence or absence of punched holes in the tape. These could work at much higher speeds (hundreds of characters per second). More sophisticated punches were also available that could run at somewhat higher speeds; Teletype's DRPE punch could operate at speeds up to 240 characters per second.

Historical impact

See also

References

  1. ↑ "Auerbach Guide to Alphanumeric Display Terminals", Auerbach Publishers, 1975
  2. ↑ "A Synopsis of Teletype Corporation History" (PDF).
  3. ↑ Telephone Engineer & Management, Volume 79, Harcourt Brace Jovanovich Publications, 1975
  4. ↑ "History of Telegraphy from the Teletype Museum" (PDF). Retrieved March 18, 2012.
  5. ↑ "Bytelines". Byte. 5 (12): 214. December 1980.
  6. ↑ "F-41D PDP-4 Brochure September 1963" (PDF). p. 5.
  7. ↑ "Digital Equipment Corporation pdp15 Price List" (PDF). p. 2.
  8. ↑ Jim Haynes. "Some Notes on Teletype Corporation" (PDF).
  9. ↑ Teletype Parts Bulletin 1184B page 35 figure 38
  10. ↑ Teletype Parts Bulletin 1184B pages 27 – 29 figure 29 – 31
  11. ↑ "Teletype Rear View of Main Assembly".
  12. ↑ Tomasi, Wayne. "Electronic Communications Systems: fundamentals through advanced", Prentice Hall, 2001, p. 531.
  13. ↑ (Manes 1994, p. 27)
  14. ↑ Patrick Suppes; Max Jerman; Guy Groen (April 1966). "Arithmetic drills and review on a computer-based teletype" (PDF). The Arithmetic Teacher. 13: 303–309.
  15. ↑ Patrick Suppes (May 19, 1971). "Computer-Assisted Instruction at Stanford" (PDF).
  16. ↑ The @-symbol, part 1 of 2, Shady Characters, July 2011
  17. ↑ "TWX in 12 Bars".
Wikimedia Commons has media related to ASR-33.
This article is issued from Wikipedia - version of the 12/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.