Corner reflector antenna

Construction of typical corner reflector antenna.

A corner reflector antenna is a type of directional antenna used at VHF and UHF frequencies.[1][2] It was invented by John D. Kraus in 1938.[3][4] It consists of a dipole driven element mounted in front of two flat rectangular reflecting screens joined at an angle, usually 90°.[1] Corner reflectors have moderate gain of 10-15 dB,[2] high front-to-back ratio of 20-30 dB, and wide bandwidth. They are widely used for UHF television receiving antennas, point-to-point communication links and data links for wireless WANs, and amateur radio antennas on the 144, 420, and 1296 MHz bands.[2] They radiate linearly polarized radio waves and can be mounted for either horizontal or vertical polarization.

The corner reflector antenna should not be confused with a corner reflector, a passive device used to reflect radio waves back toward the source.

The flat reflecting surfaces can be metal sheets, but are more often made of wire screen or rod elements parallel to the driven element, to reduce weight and wind loads on the antenna.[2] The angle θ between the sides is most commonly 90°.[1] The gain increases as the angle narrows, but the increase below 90° is minimal, and requires longer reflector screens be used. However, angles down to 45° have been used.[2]

The spacing (S) of the driven element in front of the point where the reflectors meet is approximately 0.5λ but is not very critical; for 90° antennas the gain doesn't vary more than 1.5 dB for S between 0.25λ and 0.75λ.[1][2] The radiation resistance of the dipole increases with this spacing, so the spacing can be adjusted to match the driven element to the feed line.[2] Bowtie driven elements are often used for wide bandwidth applications like television antennas.[1]

The antenna can be regarded as a form with a gain intermediate between a plane reflective array antenna and a parabolic antenna. It is particularly suitable in applications where a broadband directional antenna around one to 1 1/2 wavelengths in size is needed.[5] A parabolic dish this size has no advantage in gain over the corner reflector, so its simplicity of design and construction make it attractive.

Variations

450 MHz homemade corner reflector.
Corner reflector UHF TV antenna from 1954 with bowtie dipole driven element
Modern UHF TV antenna consisting of 3 Yagi arrays in front of a common corner reflector.
Large 120 ft high two bay corner reflector antenna for military troposcatter communication link, Massachusetts, 1955
Dual stacked corner reflector UHF TV antenna. Stacking 2 antennas increases horizontal gain 3 dB.
Vertical monopole corner reflector for HF transmission.

References

  1. 1 2 3 4 5 Stutzman, Warren L.; Thiele, Gary A. (2012). Antenna Theory and Design. John Wiley and Sons. pp. 192–194. ISBN 9780470576649.
  2. 1 2 3 4 5 6 7 Straw, R. Dean (2000). The ARRL Antenna Book (19 ed.). American Radio Relay League. pp. 18.9–18.11. ISBN 0872598179.
  3. John D. Kraus, US patent 2270314, Corner reflector antenna, filed January 31, 1940; granted January 20, 1942
  4. Kraus, John D. (1988). Antennas (PDF) (2 ed.). Tata-McGraw Hill. pp. 549–560. ISBN 0070354227.
  5. Kraus, John D. (November 1940). "The square-corner reflector beam antenna for ultra high frequencies" (PDF). QST. USA: American Radio Relay League. p. 18. Retrieved June 2, 2015.

Further reading

This article is issued from Wikipedia - version of the 11/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.