Earthen plaster

Earthen plaster (adobe plaster, dagga[1]) is a blend of clay, fine aggregate, and fiber. Other common additives include pigments, lime, casein, prickly pear cactus juice (Opuntia), manure, and linseed oil. Earthen plaster is usually applied to masonry, cob, or straw bale interiors or exteriors as a wall finish. It provides protection to the structural and insulating building components as well as texture and color.

Physical composition

All plasters and stuccos have several common features: they all contain a structural component, a binding element, and some form of fiber. Usually the term plaster refers to a wall covering made from earth, lime or gypsum, while stucco uses a cement or synthetic binding element.

Clay: the binding agent

Clay is a soil component consisting of extremely fine particles. Most clays consist of hydrous aluminum silicates, though there is a considerable amount of chemical variation among the clays. Clay is cohesive and binds to the sand and the straw, holding the mixture together, as well as securing the mixture to the wall. Clay is also plastic when wet, which makes the plaster mixture workable.

Sand: structural strength

Sand provides structure, strength, and bulk to earthen plasters. Sand consists of tiny mineral granules of rock, its parent material. Predominately composed of silicon dioxide (quartz), sand is a non-reactive substance. Because sand occurs naturally in many subsoils, all of the sand necessary may be already found in the soil.

Fiber: tensile strength and reinforcement

Dry straw, hemp fiber, cattails, coconut fiber, and animal hair are all suitable fiber choices for earthen plasters. Fiber forms a reinforcing meshwork in plasters, which helps to hold the plaster together. Fiber also provides some flexibility to a dried plaster. When clay dries it shrinks and tends to crack, but this cracking can be countered by the fiber. The fiber used in plasters must be clean, dry, and mold-free.

Additives

Additives are usually blended with the clay, sand, and natural fiber to improve the workability and strength of a plaster. Sometimes additives are added to the finish coat and other times additives may be added to all coats. Some of the most common additives are wheat flour paste, manure, cactus juice, casein (milk protein) and various natural oils such as linseed oil. Other additives include, salt, stearate, tallow, tannin, leaves and bark of certain trees, xanthum gum, alum, natural glues, gum arabic, kelp, lime, powdered milk, or the blood of livestock.

Flour paste

Cooked flour paste is a cheap natural glue that is easy to make from common ingredients. The water and flour slurry is cooked until the gluten binds the elements of the mixture, creating a durable glue. In plaster, the flour paste serves as a binding agent and a hardener.

Manure

Manure serves as a binding agent and gives plaster more body. Manure also contains small natural fibers that provide additional tensile strength as well as reduce cracking and water erosion. Different types of manure have different effects. Horse manure has a high microfiber content, but cow manure has more hardening enzymes. People have reported success with llama and alpaca dung. Manure should be fresh or fermented when mixed with plaster, as composted manure loses its enzymes and adhesive qualities. Manure should be sifted before use.

Prickly pear cactus juice

The liquid from prickly pear cactus is one of the most common additives.[2][3]

The juice from the prickly pear cactus leaf pads will serve many functions. According to some sources, it helps the plaster set and increases its stickiness or adhesion. Cactus juice also serves as a stabilizer in that it helps make earthen plasters more water-resistant and more durable. It also prevents dusting.

Cactus juice can increase plaster's workability and its ability to be formed into the desired shape. Workability depends on the water content, the shape and size distribution of its aggregate (aggregate can be rock, sand, natural fiber, etc.), the age of the plaster, and the amount of other natural binder(s) (natural binders are clay, lime, wheatpaste, cactus juice, etc.) Altering the water content, changing the aggregate mix, the age of the plaster, or changing the binders will increase or decrease the plaster's workability. Excessive water will lead to increased bleeding (surface water) and/or segregation of aggregates (when the natural binder and aggregates start to separate), with the resulting plaster having reduced quality. The use of an aggregate with an undesirable gradation can result in a very harsh mix design with a very low workability, which cannot be readily made more workable by addition of reasonable amounts of water or binder.

Cactus juice works well because it contains pectin, a water-soluble long-chain carbohydrate that acts as the binding agent to increase the adhesion of an earthen plaster. Pectin is also responsible for increasing the water resistance of an earthen plaster and has been used to augment lime plasters in both Mexico and the southwestern United States for hundreds of years.

Cactus juice is extracted by immersing cut leaves in water for as long as two weeks.[4]

Interior earthen plaster

Pure earthen plaster (plaster without lime, cement, or emulsified asphalt) is applied to interior surfaces more frequently than exteriors. Before the plaster can be applied, it must have a surface to bind to. Many types of wire mesh may be used, such as expanded-metal lath, woven wire lath, or welded wire lath. Reed mats are another option. If the plaster is being applied to a smooth surface such as drywall or plywood, a mixture of sand and wheat paste may be painted on to the surface to create the texture needed for plaster to bond.

The plaster is usually applied in three coats. The first layer of plaster is called a "scratch coat". A "comb" is used to scratch the surface horizontally or in a crisscross pattern to provide a key for the second layer. In the United States, the "comb" is commonly referred to as the "scratcher". The next layer is called the "brown coat" or leveling coat. It is leveled with tools called "Darbys" and "Rods", scraped smooth, and floated to provide a nice even surface onto which to apply the color coat. It is then allowed to dry (cure) for 7–10 days minimum to allow "checking" (shrinkage) to take place. The final layer is referred to as the "color coat" or "finishing coat", and is typically 3 mm (1/8") thick. It usually consists of clay with no fiber and little added sand. Coloring pigments are often added.

Advantages and disadvantages of earthen plaster

Earthen plasters are less toxic and energy intensive than many other wall coverings, which makes them appealing to the environmentally-conscious. Earthen Plasters are also easily repaired and inexpensive. Earth plasters resist water penetration but are permeable to water vapor. However, earthen plasters are often more labor-intensive than other forms of wall covering. If the mix is not correct in component proportions, then many other problems may occur, such as dusting and cracking. Earthen plasters are not approved by all local building codes, as some require the use of cement stabilizers or asphalt emulsion. Earthen plaster is a rare wall covering in the developed world and there is a dearth of local experts for construction and repair.

See also

Notes

  1. dagga is a Mideast and African term for mud plaster. Evans, Ianto, Linda Smiley, and Michael Smith. The hand-sculpted house: a philosophical and practical guide to building a cob cottage. White River Junction, Vt.: Chelsea Green Pub. Co., 2002. 264. Print.
  2. Cedar Rose. "Plasters & strawbale".
  3. Athena and Bill Steen. "The Straw Bale Earthen House".
  4. Guelberth, Cedar Rose; Dan Chiras (2003). The natural plaster book: earth, lime and gypsum plasters for natural homes. New Society Publishers.

Sources

This article is issued from Wikipedia - version of the 11/12/2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.