Ice screw

An ice screw. Some modern screws like this one now have a handle to assist entry and removal, whereas early models did not.

An ice screw is a threaded tubular screw used as a running belay or anchor by climbers on steep ice surface such as steep waterfall ice or alpine ice during ice climbing or crevasse rescue, to hold the climber in the event of a fall, and at belays as anchor points.[1][2]

Design

Development of ice screws for the period 1924-2000

Ice screws may come with one or more of the following: an in-built or separate ratchet mechanism to speed up placement, conical centre-hole to aid removal of ice cores, different lengths, different numbers of cutting teeth, different cutting angles, different surface finishes, and different size clip holes. Price and durability are usually design considerations too, as a usable rack of ice screws will be a significant financial investment for many climbers. Many Titanium ice screws were initially made in the former Soviet Union using Cold War-era missile technology, but were generally too brittle and so the majority of ice screws are now made of chromoly steel.

The strongest and most reliable type of ice screws currently available are the modern tubular ice screws which range in lengths from 10 to 23 cm. The approximate strength rating on a modern tubular ice screw is around 7 kN, and it has been found that short ice screws in good ice hold about 7-8 kN, no matter what the fall factor or configuration is.[3] The International Climbing and Mountaineering Federation drop test specifies that when multi-pitch lead climbing and the leader has only placed one screw (typically merely clipping one of the anchor screws) before climbing up a couple of meters and falling (a fall factor of 2), the screw must hold.[4] The dynamic ropes used in climbing can mitigate failure of an ice screw by keeping the impact forces low, especially if using a new rope that has not had any previous falls. It is rare that an ice screw fails in fall factors of 1 or less, if placed in good ice.

An older type of screw that is rarely used today is a pound-in ice screw, such as the 'snarg' and the 'warthog'. Instead of screwing these into the ice one would pound them in with a hammer from the ice tool, and then screw them out with the pick of an ice axe. The pound-ins have been largely replaced by modern tubular ice screws that are stronger and easier to use, although warthogs are being manufactured in Britain again for use in creating an anchor in frozen turf when no alternative anchor or placement is available, although it is now recommended only as 'marginal' equipment for when no other CE-tested equipment can be placed.[5][6][7]

The latest ice screws incorporate replaceable tips, thereby increasing the useful life of the screw and enhancing placements.[8]

Placement

It was once thought necessary or beneficial for ice-screws to be place horizontally or with the hanger up for optimum hold. However, it has since been found experimentally that a screw place with the tip angled up often holds as well or better. This surprising result is thought to be due to the previously underestimated role of the threads in holding the screw in place. However, horizontal placements are usually recommended.

Some climbers use tape slings to "tie-off" long ice-screws that have not been fully screwed into the ice, to reduce the leverage of a fall, which might bend or break the screw. There is some risk that such slings may move or be slice by the screw's hanger. Some novel ice screws include a hanger that can be moved down the shaft, instead of using a sling. Placing a shorter screw is usually the preferred option, hence various lengths are available.

Other uses

Long ice-screws are now often used to create V-threads (a type of thread-hole /ice-bollard). By making two ice-holes that intersect, an inexpensive but strong cord (typically static climbing accessory cord or tape, made of perlon, Dyneema or Specta) than be threaded through, making a relatively safe and cheap anchor. This can be an attractive option at belays and when ice screws are in short supply. V-threads can be particular useful as rappel or abseil points where it is often necessary to leave the final anchor behind. A piece of wire - typically a piece of old coat hanger shaped for the purpose - or a stiff flexible purpose built tool with a small hook at one end and a hanging loop at the other end, is often used to aid threading of the cord.

In the "Rosetta" project, the European Space Agency equipped its lander with multiple ice screws to obtain stability on comet surface, but they failed to hold, and the lander bounced a significant distance from the initial landing site.

Manufacturers

References

  1. Cox, Steven M.; Kris Fulsaas, ed., eds. (September 2003). Mountaineering: The Freedom of the Hills (7 ed.). Seattle: The Mountaineers. ISBN 0-89886-828-9.
  2. Semet, Matt; Mike Tea (2011). Climbing Dictionary. Seattle, USA: The Mountaineers Books. p. 124. ISBN 1-59485-502-1.
  3. Beverly and Attaway
  4. Ryan, Mick (December 2007). "The Warthog Rises Like A Phoenix From The Ashes". www.ukclimbing.com. Retrieved 5 December 2015.
  5. "Mountain Technology Warthog Turf Screw". www.needlesports.com. Retrieved 5 December 2015.
  6. "Snarg ice piton/screw". www.smhc.co.uk. Scottish Mountain Heritage Collection. Retrieved 5 December 2015.
  7. E-Climb: Ice Screw Replaceable Tips
This article is issued from Wikipedia - version of the 7/28/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.