Independent suspension

A multi-link type rear independent suspension on an AWD car. The anti-roll bar has some yellow paint on it.

Independent suspension is a broad term for any automobile suspension system that allows each wheel on the same axle to move vertically (i.e. reacting to a bump in the road) independently of each other. This is contrasted with a beam axle or deDion axle system in which the wheels are linked – movement on one side affects the wheel on the other side. Note that "independent" refers to the motion or path of movement of the wheels/suspension. It is common for the left and right sides of the suspension to be connected with anti-roll bars or other such mechanisms. The anti-roll bar ties the left and right suspension spring rates together but does not tie their motion together.

Most modern vehicles have independent front suspension (IFS). Many vehicles also have an independent rear suspension (IRS). IRS, as the name implies, has the rear wheels independently sprung. A fully independent suspension has an independent suspension on all wheels. Some early independent systems used swing axles, but modern systems use Chapman or MacPherson struts, trailing arms, multilink, or wishbones.

Independent suspension typically offers better ride quality and handling characteristics, due to lower unsprung weight and the ability of each wheel to address the road undisturbed by activities of the other wheel on the vehicle. Independent suspension requires additional engineering effort and expense in development versus a beam or live axle arrangement. A very complex IRS solution can also result in higher manufacturing costs.

The key reason for lower unsprung weight relative to a live axle design is that, for driven wheels, the differential unit does not form part of the unsprung elements of the suspension system. Instead it is either bolted directly to the vehicle's chassis or more commonly to a subframe.

The relative movement between the wheels and the differential is achieved through the use of swinging driveshafts connected via universal (U) joints, analogous to the constant-velocity (CV) joints used in front wheel drive vehicles.

Independent suspension

Suspension

Suspension is the only component that separates the driver and/or passenger from the ground. The suspension in a vehicle helps absorb harshness in the road. There are many systems and designs that do this, such as independent suspension. (Longhurst 1).

Advantages

This system provides many advantages over other suspension systems. For example, in solid axle suspension systems, when one wheel hits a bump, it affects both wheels. This will compromise traction, smoothness of the ride, and could also cause a dangerous wheel shimmy when moving at high speeds. According to "Car Suspension Bible" with independent suspension systems, the bump only affects the contacted wheel. This offers many advantages such as greater ride comfort, better traction, and safer, more stable vehicles on and off the road (Longhurst 1).

Types

Double wishbone suspension

Multi-link suspension

MacPherson strut

For more details on this topic, see MacPherson strut.

This is the most common, widely used front suspension system in cars of European and Japanese origin. It is a very simple and effective design that uses a strut-type spring and shock absorber that work as a team that will pivot on a ball joint on the single lower arm (Longhurst 2). This system has been used in the BMW E21 series, which are the first generation 3 series from 1976-1983 and this system is still used on cars today. One problem with this system is once the spring or the top plate becomes worn, the driver of a car with this system may hear a loud "clonk" like noise at full lock when the spring jumps back into place. People can often confuse this with a CV joint knock.

Transverse leaf-spring

Several independent suspension designs have featured transverse leaf springs. Most applications used multi-leaf steel springs though more recent designs have used fiber reinforced plastic (FRP, typically fibers are fiberglass) springs. In addition to spring type (multi-leaf steel, FRP), a distinction can be drawn between systems where the spring also acts as a locating link and those where the spring only acts as a spring member.

The AC Cobra is an example of a transverse, multi-leaf steal spring suspension that uses the leaf spring as the upper suspension arm. Alternatively, the 1963 Corvette's rear suspension is an example where the transverse leaf spring is used only as a ride spring. In both examples the leaf spring is centrally mounted, preventing displacement of the wheel on one side from affecting the wheel on the other side.

In 1981 General Motors pioneered the use of a FRP plastic transverse leaf spring on the third generation Corvette. As in the examples above, the spring used a single, central mount which isolated the left and right movements. The FRP spring reduced weight and eliminated the inner leaf friction as compared to the multi-leaf metal spring which was standard on the car.[1]

Rather than centrally mounting the transverse leaf spring and thus isolating the left and right sides of the springs, some manufacturers, starting with Fiat used two widely spaced spring mounts. This was first used on the front of the 1955 Fiat 600 and later at the rear on the Fiat 128. The spring is allowed to pivot inside of the mounts which allows the displacement of the spring on one side affect the other side. This mechanical communication between the left and right sides of the suspension results in an effect similar to that of an anti-roll bar.[1][2] Chevrolet Corvettes, starting with the 4th generation in 1984 have combined the dual pivot mounts with FRP leaf springs.

The transverse leaf spring is not used as commonly as it was earlier. It is very rare on modern cars, the Corvette and a few Volvo models being examples.[3] In the past it was more widely used in many Triumphs. The Herald, Vitesse, Spitfire and the GT6 all used a rear transverse leaf spring, as well as the 1995-98 Volvo 960/S90/V90 and a rare Swedish sports car incorporating the Volvo 960 rear suspension in the 1990s called the JC Indigo (Longhurst 4).

Note that this type of suspension should not be confused with earlier, rigid axle applications such as those used on early Ford cars.

References

  1. 1 2 McLellan, Dave (2002). Corvette from the Inside. Cambridge, MA: Bentley Publishers. pp. 86–87. ISBN 0-8376-0859-7.
  2. Lamm, Michael (1983). The Newest Corvette. Corvette from A to Z-51 (1st ed.). Lamm-Morada Publishing. p. 44. ISBN 978-0932128041.
  3. Stoklosa, Alexander. "10 Things You Need to Know About the 2016 Volvo XC90". Car and Driver. Retrieved 2015-08-01.
  1. Arvinmertitor Inc. "Independent Suspension for Off-highway Use." LexisNexis Academic.
  2. Longhurst, Chris. "Car Bibles : The Car Suspension Bible Page 1 of 5." The Car Maintenance Bibles. Car Bibles, 14 Oct. 2011. Web. 14 Nov. 2011. <http://www.carbibles.com/suspension_bible.html>.
  3. "independent suspension." Dictionary.com's 21st Century Lexicon. Dictionary.com, LLC. 14 Nov. 2011. <Dictionary.com
  4. Pintado, Publio, and Miguel-Angel Castell. "Independent Suspension." Vehicle System Dynamics 31.3 (1999): 137-55. EBSCO Host. Web. 14 Nov. 2011.

External links

This article is issued from Wikipedia - version of the 10/12/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.