Pelton wheel

Old Pelton wheel from Walchensee Hydroelectric Power Station, Germany.

Assembly of a Pelton wheel at Walchensee Hydroelectric Power Station, Germany.

Figure from Pelton's original patent (October 1880).

Sectional view of a Pelton turbine installation.

Bucket detail on a small turbine.

The Pelton wheel is an impulse type water turbine. It was invented by Lester Allan Pelton in the 1870s. The Pelton wheel extracts energy from the impulse of moving water, as opposed to water's dead weight like the traditional overshot water wheel. Many variations of impulse turbines existed prior to Pelton's design, but they were less efficient than Pelton's design. Water leaving those wheels typically still had high speed, carrying away much of the dynamic energy brought to the wheels. Pelton's paddle geometry was designed so that when the rim ran at half the speed of the water jet, the water left the wheel with very little speed; thus his design extracted almost all of the water's impulse energy—which allowed for a very efficient turbine.

Function

Nozzles direct forceful, high-speed streams of water against a rotary series of spoon-shaped buckets, also known as impulse blades, which are mounted around the circumferential rim of a drive wheel—also called a runner (see photo, 'Old Pelton wheel..'). As the water jet impinges upon the contoured bucket-blades, the direction of water velocity is changed to follow the contours of the bucket. Water impulse energy exerts torque on the bucket-and-wheel system, spinning the wheel; the water stream itself does a "u-turn" and exits at the outer sides of the bucket, decelerated to a low velocity. In the process, the water jet's momentum is transferred to the wheel and hence to a turbine. Thus, "impulse" energy does work on the turbine. For maximum power and efficiency, the wheel and turbine system is designed such that the water jet velocity is twice the velocity of the rotating buckets. A very small percentage of the water jet's original kinetic energy will remain in the water, which causes the bucket to be emptied at the same rate it is filled, (see conservation of mass) and thereby allows the high-pressure input flow to continue uninterrupted and without waste of energy. Typically two buckets are mounted side-by-side on the wheel, which permits splitting the water jet into two equal streams (see photo). This balances the side-load forces on the wheel and helps to ensure smooth, efficient transfer of momentum of the fluid jet of water to the turbine wheel.

Because water and most liquids are nearly incompressible, almost all of the available energy is extracted in the first stage of the hydraulic turbine. Therefore, Pelton wheels have only one turbine stage, unlike gas turbines that operate with compressible fluid. It is used for generating electricity.

Applications

Pelton wheels are the preferred turbine for hydro-power, when the available water source has relatively high hydraulic head at low flow rates, where the Pelton wheel geometry is most suitable. Pelton wheels are made in all sizes. There exist multi-ton Pelton wheels mounted on vertical oil pad bearings in hydroelectric plants. The largest units can be over 400 megawatts. The smallest Pelton wheels are only a few inches across, and can be used to tap power from mountain streams having flows of a few gallons per minute. Some of these systems use household plumbing fixtures for water delivery. These small units are recommended for use with 30 metres (100 ft) or more of head, in order to generate significant power levels. Depending on water flow and design, Pelton wheels operate best with heads from 15–1,800 metres (50–5,910 ft), although there is no theoretical limit.

Design rules

The specific speed $\eta _{s}$ parameter is independent of a particular turbine's

Compared to other turbine designs, the relatively low specific speed of the Pelton wheel, implies that the geometry is inherently a "low gear" design. Thus it is most suitable to being fed by a hydro source with a low ratio of flow to pressure, (meaning relatively low flow and/or relatively high pressure).

The specific speed is the main criterion for matching a specific hydro-electric site with the optimal turbine type. It also allows a new turbine design to be scaled from an existing design of known performance.

${\displaystyle \eta _{s}=n{\sqrt {P}}/{\sqrt {\rho }}(gH)^{5/4}}$ (dimensioned parameter), ^[1]

where:

• $n$ = Frequency of rotation (rpm)
• $P$ = Power (W)
• $H$ = Water head (m)
• $\rho$ = Density (kg/m³)

The formula implies that the Pelton turbine is geared most suitably for applications with relatively high hydraulic head H, due to the 5/4 exponent being greater than unity, and given the characteristically low specific speed of the Pelton.^[2]

Turbine physics and derivation

Energy and initial jet velocity

In the ideal (frictionless) case, all of the hydraulic potential energy (E_p = mgh) is converted into kinetic energy (E_k = mv²/2) (see Bernoulli's principle). Equating these two equations and solving for the initial jet velocity (V_i) indicates that the theoretical (maximum) jet velocity is V_i = √(2gh) . For simplicity, assume that all of the velocity vectors are parallel to each other. Defining the velocity of the wheel runner as: (u), then as the jet approaches the runner, the initial jet velocity relative to the runner is: (V_i − u).^[2] The initial jet velocity of jet is V_i

Final jet velocity

Assuming that the jet velocity is higher than the runner velocity, if the water is not to become backed-up in runner, then due to conservation of mass, the mass entering the runner must equal the mass leaving the runner. The fluid is assumed to be incompressible (an accurate assumption for most liquids). Also it is assumed that the cross-sectional area of the jet is constant. The jet speed remains constant relative to the runner. So as the jet recedes from the runner, the jet velocity relative to the runner is: −(V_i − u) = −V_i + u. In the standard reference frame (relative to the earth), the final velocity is then: V_f = (−V_i + u) + u = −V_i + 2u.

Optimal wheel speed

We know that the ideal runner speed will cause all of the kinetic energy in the jet to be transferred to the wheel. In this case the final jet velocity must be zero. If we let −V_i + 2u = 0, then the optimal runner speed will be u = V_i /2, or half the initial jet velocity.

Torque

By Newton's second and third laws, the force F imposed by the jet on the runner is equal but opposite to the rate of momentum change of the fluid, so:

F = −m( V_f − V_i) = −ρQ[(−V_i + 2u) − V_i] = −ρQ(−2V_i + 2u) = 2ρQ(V_i − u)

where (ρ) is the density and (Q) is the volume rate of flow of fluid. If (D) is the wheel diameter, the torque on the runner is: T = F(D/2) = ρQD(V_i − u). The torque is at a maximum when the runner is stopped (i.e. when u = 0, T = ρQDV_i ). When the speed of the runner is equal to the initial jet velocity, the torque is zero (i.e. when u = V_i, then T = 0). On a plot of torque versus runner speed, the torque curve is straight between these two points, (0, pQDV_i) and (V_i, 0).^[2]

Power

The power P = Fu = Tω, where ω is the angular velocity of the wheel. Substituting for F, we have P = 2ρQ(V_i − u)u. To find the runner speed at maximum power, take the derivative of P with respect to u and set it equal to zero, [dP/du = 2ρQ(V_i − 2u)]. Maximum power occurs when u = V_i /2. P_max = ρQV_i²/2. Substituting the initial jet power V_i = √(2gh), this simplifies to P_max = ρghQ. This quantity exactly equals the kinetic power of the jet, so in this ideal case, the efficiency is 100%, since all the energy in the jet is converted to shaft output.^[2]

Efficiency

A wheel power divided by the initial jet power, is the turbine efficiency, η = 4u(V_i − u)/V_i². It is zero for u = 0 and for u = V_i. As the equations indicate, when a real Pelton wheel is working close to maximum efficiency, the fluid flows off the wheel with very little residual velocity.^[2] In theory, the energy efficiency varies only with the efficiency of the nozzle and wheel, and does not vary with hydraulic head.^[3] The term "efficiency" can refer to: Hydraulic, Mechanical, Volumetric, Wheel, or overall efficiency.

System components

The conduit bringing high-pressure water to the impulse wheel is called the penstock. Originally the penstock was the name of the valve, but the term has been extended to include all of the fluid supply hydraulics. Penstock is now used as a general term for a water passage and control that is under pressure, whether it supplies an impulse turbine or not.^[2]

See also

• Peltric set
• Centrifugal pump

References

1. Sayers, A. T. (1990). Hydraulic and Compressible Flow Turbomachines. Mcgraw Hill Book Co Ltd. ISBN 978-0-07-707219-3.
2. Technical derivation of basic impulse turbine physics, by J.Calvert
3. http://people.rit.edu/rfaite/courses/tflab/Cussons/pelton/pelton.htmg

External links

• Example Hydro at Dorado Vista ranch