Antimony trioxide

Antimony(III) oxide
Names
IUPAC name
Antimony(III) oxide
Other names
Antimony sesquioxide
Antimonous oxide
Flowers of Antimony
Identifiers
1309-64-4 YesY
3D model (Jmol) Interactive image
ChemSpider 25727 YesY
ECHA InfoCard 100.013.796
KEGG C19192 YesY
RTECS number CC5650000
UNII P217481X5E YesY
Properties
Sb2O3
Molar mass 291.518 g/mol
Appearance white solid
Odor odorless
Density 5.2 g/cm3, α-form
5.67 g/cm3 β-form
Melting point 656 °C (1,213 °F; 929 K)
Boiling point 1,425 °C (2,597 °F; 1,698 K) (sublimes)
Dissolved concentration of 370 ± 37 µg/L was obtained with a loading of 10 mg/L after 7 days of exposure. Temperature varied between 20.8°C (t=0; start of the test) and 22.9°C
Solubility soluble in acid
2.087, α-form
2.35, β-form
Structure
cubic (α)<570 °C
orthorhombic (β) >570 °C
pyramidal
zero
Hazards
Safety data sheet See: data page
Harmful (Xn)
Carc. Cat. 2 (H351)
R-phrases R40
S-phrases (S2), S22, S36/37
NFPA 704
Flammability code 0: Will not burn. E.g., water Health code 2: Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury. E.g., chloroform Reactivity code 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g., liquid nitrogen Special hazards (white): no codeNFPA 704 four-colored diamond
0
2
0
Lethal dose or concentration (LD, LC):
7000 mg/kg, oral (rat)
US health exposure limits (NIOSH):
PEL (Permissible)
 TWA 0.5 mg/m3 (as Sb)[1]
REL (Recommended)
 TWA 0.5 mg/m3 (as Sb)[1]
Related compounds
Other anions
 Antimony trisulfide
Other cations
 Bismuth trioxide
Related compounds
 Diantimony tetraoxide
Antimony pentoxide
Supplementary data page
Refractive index (n),
Dielectric constant (εr), etc.
Thermodynamic
data
 Phase behaviour
solid–liquid–gas
UV, IR, NMR, MS
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
YesY verify (what is YesYN ?)
Infobox references

Antimony(III) oxide is the inorganic compound with the formula Sb2O3. It is the most important commercial compound of antimony. It is found in nature as the minerals valentinite and senarmontite.[2] Like most polymeric oxides, Sb2O3 dissolves in aqueous solutions with hydrolysis.

Production and properties

Global production of antimony(III) oxide in 2012 was 130,000 tonnes, an increase from 112,600 tonnes in 2002. China produces the largest share followed by US/Mexico, Europe, Japan and South Africa and other countries (2%).[3]

As of 2010, antimony(III) oxide was produced at four sites in EU27. It is produced via two routes, re-volatilizing of crude antimony(III) oxide and by oxidation of antimony metal. Oxidation of antimony metal dominates in Europe. Several processes for the production of crude antimony(III) oxide or metallic antimony from virgin material. The choice of process depends on the composition of the ore and other factors. Typical steps include mining, crushing and grinding of ore, sometimes followed by froth flotation and separation of the metal using pyrometallurgical processes (smelting or roasting) or in a few cases (e.g. when the ore is rich in precious metals) by hydrometallurgical processes. These steps do not take place in the EU but closer to the mining location.

Re-volatilizing of crude antimony(III) oxide

Step 1) Crude stibnite is oxidized to crude antimony(III) oxide using furnaces operating at approximately 850 to 1,000 °C. The reaction is the following:

2 Sb2S3 + 9 O2 → 2 Sb2O3 + 6 SO2

Step 2) The crude antimony(III) oxide is vaporized and condensed

Oxidation of antimony metal

Antimony metal is oxidized to antimony(III) oxide in furnaces. The reaction is exothermic. Antimony(III) oxide is formed through sublimation and recovered in bag filters (bag house). The size of the formed particles is controlled by process conditions in furnace and gas flow. The reaction can be schematically described by:

4 Sb + 3 O2 → 2 Sb2O3

Properties

Antimony(III) oxide is an amphoteric oxide, it dissolves in aqueous sodium hydroxide solution to give the meta-antimonite NaSbO2, which can be isolated as the trihydrate. Antimony(III) oxide also dissolves in concentrated mineral acids to give the corresponding salts, which hydrolyzes upon dilution with water.[4] With nitric acid, the trioxide is oxidized to antimony(V) oxide.[5]

When heated with carbon, the oxide is reduced to antimony metal. With other reducing agents such as sodium borohydride or lithium aluminium hydride, the unstable and very toxic gas stibine is produced.[6] When heated with potassium bitartrate, a complex salt potassium antimony tartrate, KSb(OH)2•C4H2O6 is formed.[5]

Structure

The structure of Sb2O3 depends on the temperature of the sample. Dimeric Sb4O6 is the high temperature (1560 °C) gas.[7] Sb4O6 molecules are bicyclic cages, similar to the related oxide of phosphorus(III), phosphorus trioxide.[8] The cage structure is retained in a solid that crystallizes in a cubic habit. The Sb-O distance is 197.7 pm and the O-Sb-O angle of 95.6°.[9] This form exists in nature as the mineral senarmontite.[8] Above 606 °C, the more stable form is orthorhombic, consisting of pairs -Sb-O-Sb-O- chains that are linked by oxide bridges between the Sb centers. This form exists in nature as the mineral valentinite.[8]

Sb4O6
senarmontite
valentinite

Uses

The annual consumption of antimony(III) oxide in the United States and Europe is approximately 10,000 and 25,000 tonnes, respectively. The main application is as flame retardant synergist in combination with halogenated materials. The combination of the halides and the antimony is key to the flame-retardant action for polymers, helping to form less flammable chars. Such flame retardants are found in electrical apparatuses, textiles, leather, and coatings.[10]

Other applications:

Safety

Antimony(III) oxide has suspected carcinogenic potential for humans.[10] Its TLV is 0.5 mg/m3, as for most antimony compounds.[11]
No other human health hazards were identified for antimony(III) oxide, and no risks to human health and the environment were identified from the production and use of antimony trioxide in daily life.

References

  1. 1 2 "NIOSH Pocket Guide to Chemical Hazards #0036". National Institute for Occupational Safety and Health (NIOSH).
  2. ↑ Greenwood, N. N.; & Earnshaw, A. (1997). Chemistry of the Elements (2nd Edn.), Oxford:Butterworth-Heinemann. ISBN 0-7506-3365-4.
  3. ↑ "Archived copy" (PDF). Archived from the original (PDF) on 2014-01-06. Retrieved 2014-01-06.
  4. ↑ Housecroft, C. E.; Sharpe, A. G. (2008). "Chapter 15: The group 15 elements". Inorganic Chemistry (3rd ed.). Pearson. p. 481. ISBN 978-0-13-175553-6.
  5. 1 2 Patnaik, P. (2002). Handbook of Inorganic Chemicals. McGraw-Hill. p. 56. ISBN 0-07-049439-8.
  6. ↑ Bellama, J. M.; MacDiarmid, A. G. (1968). "Synthesis of the Hydrides of Germanium, Phosphorus, Arsenic, and Antimony by the Solid-Phase Reaction of the Corresponding Oxide with Lithium Aluminum Hydride". Inorganic Chemistry. 7 (10): 2070–2072. doi:10.1021/ic50068a024.
  7. ↑ Wiberg, E.; Holleman, A. F. (2001). Inorganic Chemistry. Elsevier. ISBN 0-12-352651-5.
  8. 1 2 3 Wells, A. F. (1984). Structural Inorganic Chemistry. Oxford: Clarendon Press. ISBN 0-19-855370-6.
  9. ↑ Svensson, C. (1975). "Refinement of the crystal structure of cubic antimony(III) oxide, Sb2O3". Acta Crystallographica B. 31 (8): 2016–2018. doi:10.1107/S0567740875006759.
  10. 1 2 Grund, S. C.; Hanusch, K.; Breunig, H. J.; Wolf, H. U. (2005), "Antimony and Antimony Compounds", Ullmann's Encyclopedia of Industrial Chemistry, Weinheim: Wiley-VCH, doi:10.1002/14356007.a03_055.pub2
  11. ↑ Newton, P. E.; Schroeder, R. E.; Zwick, L.; Serex, T. (2004). "Inhalation Developmental Toxicity Studies In Rats With Antimony(III) oxide (Sb2O3)". Toxicologist. 78 (1-S): 38.

Further reading

External links

This article is issued from Wikipedia - version of the 10/28/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.