Rotary engine

This article is about a type of piston engine with a rotating crankcase. For the pistonless Wankel engine, see Wankel engine. For other engines described as "rotary", see rotary engine (disambiguation).
An 80 horsepower (60 kW) rated Le Rhône 9C, a typical rotary engine of WWI. The copper pipes carry the fuel-air mixture from the crankcase to the cylinder heads acting collectively as an intake manifold.
Animation of a seven-cylinder rotary engine with every-other-piston firing order.

The rotary engine was an early type of internal-combustion engine, usually designed with an odd number of cylinders per row in a radial configuration, in which the crankshaft remained stationary in operation, with the entire crankcase and its attached cylinders rotating around it as a unit. Its main application was in aviation, although it also saw use before its primary aviation role, in a few early motorcycles and automobiles.

This type of engine was widely used as an alternative to conventional inline engines (straight or V) during World War I and the years immediately preceding that conflict. It has been described as "a very efficient solution to the problems of power output, weight, and reliability".[1]

By the early 1920s, however, the inherent limitations of this type of engine had rendered it obsolete, with the power output increasingly going into overcoming the air-resistance of the spinning engine itself. The rotating mass of the engine also caused significant gyroscopic precession: depending on the type of aircraft, this produced stability and control problems, especially for inexperienced pilots. Another factor in the demise of the rotary was the fundamentally inefficient total-loss oiling system, caused by the need to aspirate the fuel/air mixture through the hollow crankshaft and crankcase along with the lubricating medium, as in a two-stroke engine.

Description

A Le Rhône 9C engine installed on a Sopwith Pup fighter aircraft at the Fleet Air Arm Museum.
Note the narrowness of the mounting pedestal to the fixed crankshaft (2013)

A rotary engine is essentially a standard Otto cycle engine, but instead of having a fixed cylinder block with rotating crankshaft as with a conventional radial engine, the crankshaft remains stationary and the entire cylinder block rotates around it. In the most common form, the crankshaft was fixed solidly to the airframe, and the propeller was simply bolted to the front of the crankcase.

Three key factors contributed to the rotary engine's success at the time:[2]

Most rotary engines were arranged with the cylinders pointing outwards from a single crankshaft, in the same general form as a radial, but there were also rotary boxer engines[3] and even one-cylinder rotaries.

Like radial engines, rotaries were generally built with an odd number of cylinders (usually either 7 or 9), so that a consistent every-other-piston firing order could be maintained, to provide smooth running. Rotary engines with an even number of cylinders were mostly of the "two row" type.

Distinction between "rotary" and "radial" engines

Rotary and radial engines look strikingly similar when they are not running and can easily be confused, since both have cylinders arranged radially around a central crankshaft. Unlike the rotary engine, however, radial engines use a conventional rotating crankshaft in a fixed engine block.

The Musee de l'Air in Paris has on display a special, "sectioned" working model of an engine with seven "radially disposed" cylinders. It alternates between "rotary" and "radial" modes to demonstrate the difference between the internal motions of the two types of engine.[4]

Rotary engine control

Monosoupape rotaries

It is often asserted that rotary engines had no carburetor and hence power could only be reduced by intermittently cutting the ignition using a "blip" switch. This was almost literally true of the "Monosoupape" (single valve) type, which took most of the air into the cylinder through the exhaust valve, which remained open for a portion of the downstroke of the piston. Thus the richness of the mixture in the cylinder could not be controlled via the crankcase intake. The "throttle" (fuel valve) of a monosoupape provided only a very limited degree of speed regulation, as opening it made the mixture too rich, while closing it made it too lean (in either case quickly stalling the engine, or damaging the cylinders). Early models featured a pioneering form of variable valve timing in an attempt to give greater control, but this caused the valves to burn and therefore it was abandoned.[5]

The only way of running a Monosoupape engine smoothly at reduced revs was with a switch that changed the normal firing sequence so that each cylinder fired only once per two or three engine revolutions, but the engine remained more or less in balance.[6] As with excessive use of the "blip" switch: running the engine on such a setting for too long resulted in large quantities of unburned fuel and oil in the exhaust, and gathering in the lower cowling, where it was a notorious fire hazard.

"Normal" rotaries

Most rotaries however, had normal inlet valves, so that the fuel (and lubricating oil) was taken into the cylinders already mixed with air - as in a normal four-stroke engine. Although a conventional carburetor, with the ability to keep the fuel/air ratio constant over a range of throttle openings, was precluded by the spinning crankcase; it was possible to adjust the air supply through a separate flap valve or "bloctube". The pilot needed to set the throttle to the desired setting (usually full open) and then adjust the fuel/air mixture to suit using a separate "fine adjustment" lever that controlled the air supply valve (in the manner of a manual choke control). Due to the rotary engine's large rotational inertia, it was possible to adjust the appropriate fuel/air mixture by trial and error without stalling it, although this varied between different types of engine, and in any case it required a good deal of practice to acquire the necessary knack. After starting the engine with a known setting that allowed it to idle, the air valve was opened until maximum engine speed was obtained.

Throttling a running engine back to reduce revs was possible by closing off the fuel valve to the required position while re-adjusting the fuel/air mixture to suit. This process was also tricky, so that throttling back, especially when landing, was often accomplished by intermittently cutting the ignition using the blip switch.

Cutting cylinders using ignition switches had the drawback of letting fuel continue to pass through the engine, oiling up the spark plugs and making smooth restarting problematic. Also, the raw oil-fuel mix could collect in the cowling. As this could cause a serious fire when the switch was released, it became common practice for part or all of the bottom of the basically circular cowling on most rotary engines to be cut away, or fitted with drainage slots.

By 1918 a Clerget handbook advised maintaining all necessary control by using the fuel and air controls, and starting and stopping the engine by turning the fuel on and off. The recommended landing procedure involved shutting off the fuel using the fuel lever, while leaving the blip switch on. The windmilling propeller made the engine continue to spin without delivering any power as the aircraft descended. It was important to leave the ignition on to allow the spark plugs to continue to spark and keep them from oiling up, so that the engine could (if all went well) be restarted simply by re-opening the fuel valve. Pilots were advised to not use an ignition cut out switch, as it would eventually damage the engine.[5]

Pilots of surviving or reproduction aircraft fitted with rotary engines still find, however, that the blip switch is useful while landing, as it provides a more reliable, quicker way to initiate power if needed, rather than risk a sudden engine stall, or the failure of a windmilling engine to restart at the worst possible moment.

History

Millet

An 1897 Félix Millet motorcycle.

Félix Millet showed a 5-cylinder rotary engine built into a bicycle wheel at the Exposition Universelle in Paris in 1889. Millet had patented the engine in 1888, so must be considered the pioneer of the internal combustion rotary engine. A machine powered by his engine took part in the Paris-Bordeaux-Paris race of 1895 and the system was put into production by Darracq and Company London in 1900.[7]

Hargrave

Lawrence Hargrave first developed a rotary engine in 1889 using compressed air, intending to use it in powered flight. Materials weight and lack of quality machining prevented it becoming an effective power unit.[8]

Balzer

Stephen Balzer of New York, a former watchmaker, constructed rotary engines in the 1890s.[9] He was interested in the rotary layout for two main reasons:

Balzer produced a 3-cylinder, rotary engined car in 1894, then later became involved in Langley's Aerodrome attempts, which bankrupted him while he tried to make much larger versions of his engines. Balzer's rotary engine was later converted to static radial operation by Langley's assistant, Charles M. Manly, creating the notable Manly-Balzer engine.

De Dion-Bouton

The famous De Dion-Bouton company produced an experimental 4-cylinder rotary engine in 1899. Though intended for aviation use, it was not fitted to any aircraft.[7]

Adams-Farwell

Main article: Adams-Farwell
An Adams-Farwell five cylinder rotary adapted for helicopter experimentation

The Adams-Farwell firm's automobiles, with the firm's first rolling prototypes using 3-cylinder rotary engines designed by Fay Oliver Farwell in 1898, led to production Adams-Farwell cars with first the 3-cylinder, then very shortly thereafter 5-cylinder rotary engines later in 1906, as another early American automaker utilizing rotary engines expressly manufactured for automotive use. Emil Berliner sponsored its development of the 5-cylinder Adams-Farwell rotary engine design concept as a lightweight power unit for his unsuccessful helicopter experiments. Adams-Farwell engines later powered fixed-wing aircraft in the US after 1910. It has also been asserted that the Gnôme design was derived from the Adams-Farwell, since an Adams-Farwell car is reported to have been demonstrated to the French Army in 1904. In contrast to the later Gnôme engines, and much like the later Clerget 9B and Bentley BR1 aviation rotaries, the Adams-Farwell rotaries had conventional exhaust and inlet valves mounted in the cylinder heads.[7]

Gnome

Sectional views of Gnome engine

The Gnome engine was the work of the three Seguin brothers, Louis, Laurent and Augustin. They were talented engineers and the grandsons of famous French engineer Marc Seguin. In 1906 the eldest brother, Louis, had formed the Société des Moteurs Gnome[10] to build stationary engines for industrial use, having licensed production of the Gnom single-cylinder stationary engine from Motorenfabrik Oberursel—who, in turn, built licensed Gnome engines for German aircraft during World War I.

Louis was joined by his brother Laurent who designed a rotary engine specifically for aircraft use, using Gnom engine cylinders. The brothers' first experimental engine is said to have been a 5-cylinder model that developed 34 hp (25 kW), and was a radial rather than rotary engine, but no photographs survive of the five-cylinder experimental model. The Seguin brothers then turned to rotary engines in the interests of better cooling, and the world's first production rotary engine, the 7-cylinder, air-cooled 50 hp (37 kW) "Omega" was shown at the 1908 Paris automobile show. The first Gnome Omega built still exists, and is now in the collection of the Smithsonian's National Air and Space Museum.[11] The Seguins used the highest strength material available - recently developed nickel steel alloy - and kept the weight down by machining components from solid metal, using the best American and German machine tools to create the engine's components; the cylinder wall of a 50 hp Gnome was only 1.5 mm thick, while the connecting rods were milled with deep central channels to reduce weight. While somewhat low powered in terms of units of power per litre, its power-to-weight ratio was an outstanding 1 hp (0.75 kW) per kg.

The following year, 1909, the inventor Roger Ravaud fitted one to his Aéroscaphe, a combination hydrofoil/aircraft, which he entered in the motor boat and aviation contests at Monaco. However, Henry Farman's use of the Gnome at the famous Rheims aircraft meet that year brought it to prominence, when he won the Grand Prix for the greatest non-stop distance flown—180 kilometres (110 mi)—and also set a world record for endurance flight. The very first successful seaplane flight, of Henri Fabre's Le Canard, was powered by a Gnome Omega on March 28, 1910 near Marseille.

Production of Gnome rotaries increased rapidly, with some 4,000 being produced before World War I, and Gnome also produced a two-row version (the 100 h.p. Double Omega), the larger 80 hp Gnome Lambda and the 160 hp two-row Double Lambda. By the standards of other engines of the period, the Gnome was considered not particularly temperamental, and was credited as the first engine able to run for ten hours between overhauls.

In 1913 the Seguin brothers introduced the new Monosoupape ("single valve") series, which replaced inlet valves in the pistons by using a single valve in each cylinder head, which doubled as inlet and exhaust valve. The engine speed was controlled by varying the opening time and extent of the exhaust valves using levers acting on the valve tappet rollers, a system later abandoned due to valves burning. The weight of the Monosoupape was slightly less than the earlier two-valve engines, and it used less lubricating oil. The 100 hp Monosoupape was built with 9 cylinders, and developed its rated power at 1,200 rpm.[12] The later 160 hp nine-cylinder Gnome 9N rotary engine used the Monosoupape valve design, and was the last known rotary engine design to use such a cylinder head valving format.

A German Oberursel U.III engine on museum display

Rotary engines produced by the Clerget and Le Rhône companies used conventional pushrod-operated valves in the cylinder head, but used the same principle of drawing the fuel mixture through the crankshaft, with the Le Rhônes having prominent copper intake tubes running from the crankcase to the top of each cylinder to admit the intake charge.

The 80 hp (60 kW) seven-cylinder Gnome was the standard at the outbreak of World War I, as the Gnome Lambda, and it quickly found itself being used in a large number of aircraft designs. It was so good that it was licensed by a number of companies, including the German Motorenfabrik Oberursel firm who designed the original Gnom engine. Oberursel was later purchased by Fokker, whose 80 hp Gnome Lambda copy was known as the Oberursel U.0. It was not at all uncommon for French Gnomes, as used in the earliest examples of the Bristol Scout biplane, to meet German versions, powering Fokker E.I Eindeckers, in combat, from the latter half of 1915 on.

The only attempts to produce twin-row rotary engines in any volume were undertaken by Gnome, with their Double Lambda fourteen-cylinder 160 hp design, and with the German Oberursel firm's early World War I clone of the Double Lambda design, the U.III of the same power rating. While an example of the Double Lambda went on to power one of the Deperdussin Monocoque racing aircraft to a world-record speed of nearly 204 km/h (126 mph) in September 1913, the Oberursel U.III is only known to have been fitted into a few German production military aircraft, the Fokker E.IV fighter monoplane and Fokker D.III fighter biplane, both of whose failures to become successful combat types were partially due to the poor quality of the German powerplant, which was prone to wearing out after only a few hours of combat flight.

World War I

A Siemens-Halske Sh.III preserved at the Technisches Museum Wien (Vienna Museum of Technology). This engine powered a number of German fighter aircraft types towards the end of World War 1

The favourable power-to-weight ratio of the rotaries was their greatest advantage. While larger, heavier aircraft relied almost exclusively on conventional in-line engines, many fighter aircraft designers preferred rotaries right up to the end of the war.

Rotaries had a number of disadvantages, notably very high fuel consumption, partially because the engine was typically run at full throttle, and also because the valve timing was often less than ideal. Oil consumption was also very high. Due to primitive carburetion and absence of a true sump, the lubricating oil was added to the fuel/air mixture. This made engine fumes heavy with smoke from partially burnt oil. Castor oil was the lubricant of choice, as its lubrication properties were unaffected by the presence of the fuel, and its gum-forming tendency was irrelevant in a total-loss lubrication system. An unfortunate side-effect was that World War I pilots inhaled and swallowed a considerable amount of the oil during flight, leading to persistent diarrhoea.[13] Flying clothing worn by rotary engine pilots was routinely soaked with oil.

The rotating mass of the engine also made it, in effect, a large gyroscope. During level flight the effect was not especially apparent; however, when turning, the gyroscopic precession became noticeable. Due to the direction of the engine's rotation, left turns required effort and happened relatively slowly, combined with a tendency to nose up, while right turns were almost instantaneous, with a tendency for the nose to drop.[14] In some aircraft, this could be advantageous in situations such as dogfights. The Sopwith Camel suffered to such an extent that it required left rudder for both left and right turns, and could be extremely hazardous if the pilot applied full power at the top of a loop at low airspeeds. Trainee Camel pilots were warned to attempt their first hard right turns only at altitudes above 1,000 ft (300 m).[15] The Camel's most famous German foe, the Fokker Dr.I triplane, also used a rotary engine, usually the Oberursel Ur.II clone of the French-built Le Rhone 9J 110 hp powerplant.

Even before the First World War, attempts were made to overcome the inertia problem of rotary engines. As early as 1906 Charles Benjamin Redrup had demonstrated to the Royal Flying Corps at Hendon a 'Reactionless' engine in which the crankshaft rotated in one direction and the cylinder block in the opposite direction, each one driving a propeller. A later development of this was the 1914 reactionless 'Hart' engine designed by Redrup in which there was only one propeller connected to the crankshaft, but it rotated in the opposite direction to the cylinder block, thereby largely cancelling out negative effects. This proved too complicated for reliable operation and Redrup changed the design to a static radial engine, which was later tried in the experimental Vickers F.B.12b and F.B.16 aircraft,[16] unfortunately without success.

As the war progressed, aircraft designers demanded ever-increasing amounts of power. Inline engines were able to meet this demand by improving their upper rev limits, which meant more power. Improvements in valve timing, ignition systems, and lightweight materials made these higher revs possible, and by the end of the war the average engine had increased from 1,200 rpm to 2,000. The rotary was not able to do the same due to the drag of the rotating cylinders through the air. For instance, if an early-war model of 1,200 rpm increased its revs to only 1,400, the drag on the cylinders increased 36%, as air drag increases with the square of velocity. At lower rpm, drag could simply be ignored, but as the rev count rose, the rotary was putting more and more power into spinning the engine, with less remaining to provide useful thrust through the propeller.

Animation of the Siemens-Halske Sh.III's internal operation

One clever attempt to rescue the design, in a similar manner to Redrup's British "reactionless" engine concept, was made by Siemens AG. The crankcase (with the propeller still fastened directly to the front of it) and cylinders spun counterclockwise at 900 rpm, as seen externally from a "nose on" viewpoint, while the crankshaft and other internal parts spun clockwise at the same speed, so the set was effectively running at 1800 rpm. This was achieved by the use of bevel gearing at the rear of the crankcase, resulting in the eleven-cylindered Siemens-Halske Sh.III, with less drag and less net torque.[17] Used on several late war types, notably the Siemens-Schuckert D.IV fighter, the new engine’s low running speed, coupled with large, coarse pitched propellers that sometimes had four blades (as the SSW D.IV used), gave types powered by it outstanding rates of climb, with some examples of the late production Sh.IIIa powerplant even said to be delivering as much as 240 hp.[18]

One new rotary powered aircraft, Fokker's own D.VIII, was designed at least in part to provide some use for the Oberursel factory's backlog of otherwise redundant 110 hp (82 kW) Ur.II engines, themselves clones of the Le Rhône 9J rotary.

Because of the Allied blockade of shipping, the Germans were increasingly unable to obtain the castor oil necessary to properly lubricate their rotary engines. Substitutes were never entirely satisfactory - causing increased running temperatures and reduced engine life.[19][20][21]

Postwar

By the time the war ended, the rotary engine had become obsolete, and it disappeared from use quite quickly. The British Royal Air Force probably used rotary engines for longer than most other operators. The RAF's standard post-war fighter, the Sopwith Snipe, used the Bentley BR2 rotary as the most powerful (at some 230 hp (170 kW)) rotary engine ever built by the Allies of World War I. The standard RAF training aircraft of the early post-war years, the 1914-origin Avro 504K, had a universal mounting to allow the use of several different types of low powered rotary, of which there was a large surplus supply. Similarly, the Swedish FVM Ö1 Tummelisa advanced training aircraft, fitted with a Le-Rhone-Thulin 90 hp (67 kW) rotary engine, served until the mid thirties.

However, designers had to balance the cheapness of war-surplus engines against their poor fuel efficiency and the operating expense of their total-loss lubrication system, and by the mid-1920s, rotaries had been more or less completely displaced even in British service, largely by the new generation of air-cooled "stationary" radials such as the Armstrong Siddeley Jaguar and Bristol Jupiter.

Experiments with the concept of the rotary engine continued, however.

The first version of the 1921 Michel engine, an unusual opposed-piston cam engine, used the principle of a rotary engine, in that its "cylinder block" rotated. This was soon replaced by a version with the same cylinders and cam, but with stationary cylinders and the cam track rotating in lieu of a crankshaft. A later version abandoned the cam altogether and used three coupled crankshafts.

By 1930 the Soviet helicopter pioneers, Boris N. Yuriev and Alexei M. Cheremukhin, both employed by Tsentralniy Aerogidrodinamicheskiy Institut (TsAGI, the Central Aerohydrodynamic Institute), constructed one of the first practical single-lift rotor machines with their TsAGI 1-EA single rotor helicopter, powered by two Soviet-designed and built M-2 rotary engines, themselves up-rated copies of the Gnome Monosoupape rotary engine of World War I. The TsAGI 1-EA set an unofficial altitude record of 605 meters (1,985 ft) with Cheremukhin piloting it on 14 August 1932 on the power of its twinned M-2 rotary engines.[22]

Use in cars and motorcycles

Although rotary engines were mostly used in aircraft, a few cars and motorcycles were built with rotary engines. Perhaps the first was the Millet motorcycle of 1892. A famous motorcycle, winning many races, was the Megola, which had a rotary engine inside the front wheel. Another motorcycle with a rotary engine was Charles Redrup's 1912 Redrup Radial, which was a three-cylinder 303 cc rotary engine fitted to a number of motorcycles by Redrup.

In 1904 the Barry engine, also designed by Redrup, was built in Wales: a rotating 2-cylinder boxer engine weighing 6.5 kg[3] was mounted inside a motorcycle frame.

In the 1940s Cyril Pullin developed the Powerwheel, a wheel with a rotating one-cylinder engine, clutch and drum brake inside the hub, but it never entered production.

Cars with rotary engines were built by American companies Adams-Farwell, Bailey, Balzer and Intrepid, amongst others.

Other rotary engines

Besides the configuration of cylinders moving around a fixed crankshaft, several different engine designs are also called rotary engines. The most notable pistonless rotary engine, the Wankel rotary engine has been used by NSU in the Ro80 car, by Mazda in a variety of cars such as the RX-series, and in some experimental aviation applications.

In the late 1970s a concept engine called the Bricklin-Turner Rotary Vee was tested.[23][24] The Rotary Vee is similar in configuration to the elbow steam engine. Piston pairs connect as solid V shaped members, with each end floating in a pair of rotating cylinders clusters. The rotating cylinder cluster pairs are set with their axes at a wide V angle. The pistons in each cylinder cluster move parallel to each other instead of a radial direction, This engine design has not gone into production. The Rotary Vee was intended to power the Bricklin SV-1.

See also

Notes

  1. ↑ Nahum, Andrew (1999). The Rotary Aero Engine. NMSI Trading Ltd. p. 40. ISBN 1-900747-12-X.
  2. ↑ Air Board Technical Notes, RAF Air Board, 1917, reprinted by Camden Miniature Steam Services, 1997
  3. 1 2 "Charles Benjamin Redrup". Retrieved 2008-04-11.
  4. ↑ Vimeo video of Musee de l'Air "rotary/radial" alternating aviation cross-sectional kinetic model display
  5. 1 2 Nahum, Andrew (1999). The Rotary Aero Engine. NMSI Trading Ltd. pp. 44–45. ISBN 1-900747-12-X.
  6. ↑ Donovan, Frank; Frank Robert Donovan (1962). The Early Eagles. Dodd, Mead. p. 154.
  7. 1 2 3 Nahum, Andrew (1999). The Rotary Aero Engine. NMSI Trading Ltd. p. 20. ISBN 1-900747-12-X.
  8. ↑ Hargrave, Lawrence (1850 – 1915). Australian Dictionary of Biography Online.
  9. ↑ "Balzer automobile patents". National Museum of American History.
  10. ↑ "SAFRAN" (in French). Retrieved 2009-09-14. Le 6 juin 1905, Louis et Laurent Seguin fondent la société des moteurs Gnome à Gennevilliers
  11. ↑ "Gnome Omega No. 1 Rotary Engine". Smithsonian Institution. Retrieved 14 April 2012.
  12. ↑ Vivian, E. Charles (2004). A History of Aeronautics. Kessinger Publishing. p. 255. ISBN 1-4191-0156-0.
  13. ↑ Arthur Gould Lee (2012). Open Cockpit: A Pilot of the Royal Flying Corps. Grub Street. ISBN 978-1-908117-25-0.
  14. ↑ McCutcheon, Kimble D. "Gnome Monosoupape Type N Rotary" (PDF). Aircraft Engine Historical Society. Retrieved 2008-05-01.
  15. ↑ Abzug, Malcolm J.; E. Eugene Larrabee (2002). Airplane Stability and Control. Cambridge University Press. p. 9. ISBN 0-521-80992-4. Cite uses deprecated parameter |coauthors= (help)
  16. ↑ Fairney, William (2007). The Knife and Fork Man - The Life and Works of Charles Benjamin Redrup. Diesel Publishing. ISBN 978-0-9554455-0-7.
  17. ↑ Gray, Peter L. (1966). Aircraft in Profile No.86 — The Siemens Schuckert D.III & IV. Leatherhead, Surrey, England: Profile Publications, Ltd. pp. 4 & 5. Retrieved August 7, 2013.
  18. ↑ Gray, Peter L. (1966). Aircraft in Profile No.86 — The Siemens Schuckert D.III & IV. Leatherhead, Surrey, England: Profile Publications, Ltd. p. 12. Retrieved August 7, 2013.
  19. ↑ Guilmartin, John F., Jr. (1994). "Technology and Strategy: What Are the Limits?". Two Historians in Technology and War. United States Army War College, Strategic Studies Institute. p. 10. ISBN 1428915222.
  20. ↑ Fisher, Suzanne Hayes (1999). "Aircraft, production during the war". In Spencer C. Tucker; Laura Matysek Wood; Justin D. Murphy. The European Powers in the First World War: An Encyclopedia. Taylor & Francis. p. 10. ISBN 081533351X.
  21. ↑ U.S. Tariff Commission (1921). Tariff Information Surveys on the Articles in Paragraphs 44 and 45 of the Tariff Act of 1913. Washington, D.C.: Government Printing Office. p. 40.
  22. ↑ Savine, Alexandre. "TsAGI 1-EA." ctrl-c.liu.se, 24 March 1997. Retrieved 12 December 2010.
  23. ↑ Popular Science. August 1974. Missing or empty |title= (help)
  24. ↑ Popular Science. April 1976. Missing or empty |title= (help)
Wikimedia Commons has media related to Rotary aircraft engines.
Wikimedia Commons has media related to Non-aircraft rotary engines.
This article is issued from Wikipedia - version of the 11/26/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.