CGR 1st Class 2-6-0 1876 BP

This article is about one of several different Cape Government Railways locomotive types to be designated "1st Class". For the others, see Cape Government Railways 1st Class locomotives.
CGR 1st Class 2-6-0 1876 BP
OVGS 2nd Class 2-6-0ST
South African Class 01 2-6-0 1876

1st Class 2-6-0 at Bellville, numbered 7 aft of the smokebox
Type and origin
Power type Steam
Designer Beyer, Peacock and Company
Builder Beyer, Peacock and Company
Avonside Engine Company
Serial number BP 1571-1580
Avonside 1171-1178
Build date 1876-1877
Total produced 18
Specifications
Configuration 2-6-0 (Mogul)
Driver 2nd coupled axle
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Leading dia. 24 in (610 mm)
Coupled dia. 39 in (991 mm)
Tender wheels 33 in (838 mm)
Wheelbase 27 ft 11 in (8,509 mm)
 • Engine 10 ft 9 in (3,277 mm)
 • Coupled 7 ft 2 in (2,184 mm)
 • Tender 8 ft (2,438 mm)
Wheel spacing
(Asymmetrical)		 1-2: 3 ft 5 in (1,041 mm)
2-3: 3 ft 9 in (1,143 mm)
Length:
 ​
 • Over couplers 37 ft 8 in (11,481 mm)
Height 11 ft (3,353 mm)
Frame type Plate
Axle load 5 LT 12 cwt (5,690 kg)
 • Leading 3 LT 15 cwt 1 qtr (3,823 kg)
 • 1st coupled 5 LT 12 cwt (5,690 kg)
 • 2nd coupled 5 LT 9 cwt 3 qtr (5,576 kg)
 • 3rd coupled 5 LT 5 cwt 1 qtr (5,347 kg)
Adhesive weight 16 LT 7 cwt (16,610 kg)
Loco weight 20 LT 2 cwt 1 qtr (20,440 kg)
Tender weight 17 LT 17 cwt (18,140 kg)
Total weight 37 LT 19 cwt 1 qtr (38,570 kg)
Tender type 3-axle
Fuel type Coal
Fuel capacity 2 LT 10 cwt (2.5 t)
Water cap 1,700 imp gal (7,730 l)
Firebox type Round-top
 • Firegrate area 9 1⁄2 sq ft (0.88 m2)
Boiler:
 ​
 • Pitch 5 ft 2 in (1,575 mm)
 • Tube plates 9 ft 5 1⁄4 in (2,877 mm)
 • Small tubes 116: 1 3⁄4 in (44 mm)
Boiler pressure 130 psi (896 kPa)
Safety valve Salter
Heating surface 536 sq ft (49.8 m2)
 • Tubes 492 sq ft (45.7 m2)
 • Firebox 44 sq ft (4.1 m2)
Cylinders Two
Cylinder size 12 in (305 mm) bore
20 in (508 mm) stroke
Valve gear Stephenson
Valve type Slide
Train brakes Tender & guard's van
Couplers Johnston link-and-pin
Performance figures
Tractive effort 7,200 lbf (32 kN) @ 75%
Career
Operators Cape Government Railways
Sudan
OVGS
Transvaal collieries
Imperial Military Railways
Central South African Railways
South African Railways
Class CGR 1st Class, SAR Class 01
Number in class 18
Numbers W7-W24
Official name Peacock (No. W7)
Delivered 1876-1877
First run 1876
Withdrawn 1916

The Cape Government Railways 1st Class 2-6-0 of 1876 by Beyer, Peacock and Avonside was a South African steam locomotive from the pre-Union era in the Cape of Good Hope.

In 1876 and 1877, the Cape Government Railways placed eighteen 2-6-0 Mogul type locomotives in freight service on the Cape Western system. They were built by Beyer, Peacock and Avonside and were designated 1st Class when a classification system was adopted.[1][2]

Manufacturers

Ten 2-6-0 tender goods locomotives were delivered to the Cape Government Railways (CGR) from Beyer, Peacock and Company in 1876, numbered in the range from W7 to W16 for the Western System. The first one, no. W7, was named Peacock. The following year, another eight were delivered from Avonside Engine Company, numbered in the range from W17 to W24. All of them were equipped with six-wheeled tenders.[1][2][3]

While they were acquired as goods locomotives, they were used on all kinds of traffic, including shunting. These locomotives were later designated 1st Class when a locomotive classification system was introduced by the CGR.[1]

Characteristics

The cylinders were arranged horizontally and outside the engine frame. The slide valves, mounted above the cylinders, were actuated by Stephenson's Link motion. The engine's boiler barrel setions were not arranged telescopically, but were jointed end-to-end with butt straps.[4]

Brakes

The six-wheeled tender was equipped with a hand brake and wooden brake blocks, but the engine's coupled wheels were not braked. Until c. 1876, it was universal practice with tender engines to not fit brakes on the coupled wheels. Train braking was therefore by means of the tender's hand brake and the brakes on the guard's van, or brake van, with reliance on the guard to apply or release the van's brakes upon whistle signals from the driver.[4]

Feedwater

The feedwater pump was fitted to the front frame stretcher and was driven by an eccentric on the driver axle. The locomotive was also equipped with a small feedwater injector, invented by the French engineer Henri Giffard in 1852, for use in cases of emergency. The pump and the injector feed had separate clack boxes.[4]

The axle-driven feedwater pump had two disadvantages, the hydraulic ram action of the pump when running at high speed which tended to cause burst pumps and pipe connections, and the inability to feed the boiler while the engine was stationary. It was abandoned by locomotive design engineers once the injector feed system had been proven successful.[4]

Service

Cape Government Railways

As a result of the distances involved on the new lines which were being built into the arid Karoo and the limited onboard coal and water capacities of tank engines, the CGR favoured tender locomotives over tank locomotives for mainline work from the outset. At the time these locomotives entered service in 1876, the Western System's line from Cape Town was completed to Worcester, having been officially opened on 16 June 1876.[5]

The line from Worcester up the Hex River rail pass to Montagu Road, was completed in 1877. Passengers en route to Kimberley detrained at Montagu Road, where they usually spent the night in the local hotel before proceeding to Matjiesfontein by horse-drawn coach the following day.[5]

Apart from some which were sold or disposed of between 1884 and 1896, all but one these locomotives remained on the Western System. Until c. 1882, they saw service on all parts of the system, working out of Cape Town deeper into the Karoo, as the line was being extended and opened to Beaufort West and beyond. By 1890 one of them, no. W17, was transferred to the Midland System, where it was renumbered 414.[1][4]

Cape Central Railways

CCR 1st Class engine with no. 18 aft of the smokebx

Early in 1883, the Cape of Good Hope Government, by Act 16, authorised the Cape Central Railways (CCR) to construct a 42 miles (68 kilometres) long line from Worcester via Robertson to Roodewal. The amount of £100,000 was contributed to the cost of construction by Government, on condition that the line be made equal in all respects to the CGR lines.[6]

The CCR's line was opened to traffic in 1887 and most of its rolling stock was purchased from the CGR. The first locomotives to serve on the CCR were some of these Beyer, Peacock engines, which were initially used as construction locomotives and later for shunting.[6]

As a result of continued ox-wagon competition, the CCR went bankrupt in 1892. In January 1893, the whole of the assets of the CCR was purchased by a new company, the New Cape Central Railways (NCCR).[6]

Sudan

Four of these locomotives, numbers W7, W9, W13 and W14, were sold to Sudan in October 1884. Since number gap-filling was at the order of the day on the CGR at the time, the locomotives in the number range from 21 to 24 were renumbered to 7, 9, 13 and 14 at some stage between 1886 and 1888.[1][7]

Transvaal collieries

Two of these locomotives are known to have been sold to collieries in the Transvaal Republic at some stage between 1890 and 1895. By 1895, one was in service at Great Eastern Colliery and another at the Cassel Coal Company, both near Springs on the East Rand. Boiler records show them as 1877-built, which identifies them as from the Avonside batch of locomotives, and the most likely candidates are two of the three locomotives numbers 7, 9 and 14 (formerly numbers 21, 22 and 24), one of which possibly became no. 303 Bloemfontein.[7][8]

Oranje-Vrijstaat Gouwerment-Spoorwegen

Photographic evidence shows that at least one of these locomotives was rebuilt to a saddle-tank engine. Towards the end of 1896, a saddle-tank locomotive was sold to the Oranje-Vrijstaat Gouwerment-Spoorwegen (OVGS), where it was classified as 2nd Class, allocated number 3 and named Bloemfontein. It was employed as shop locomotive at the Bloemfontein railway workshops.[1][9]

During the Second Boer War, engine no. 3 Bloemfontein came onto the roster of the Imperial Military Railways (IMR) as no. 303 Bloemfontein. When the war ended, the IMR was transformed into the Central South African Railways (CSAR) and the locomotive retained the number 303.[1][10]

OVGS no. 3, CSAR no. 303 Bloemfontein, c. 1902

Until photographic evidence proved differently, it had been believed that this locomotive was rebuilt from the Midland System's 1st Class 2-6-0 engine no. M22, built by Kitson and Company in 1876. However, judging from the unique position of the steam dome on locomotive no. 303, depicted here after a turntable mishap, it was rebuilt from one of the locomotives built by Beyer, Peacock and Avonside, on which the steam dome was located further back, closer to the cab than usual.[1][8]

The locomotive identification error may have had its origin on the original engine power chart of the OVGS, on which the caption described the engine as "Second Class Kitson" even though the accompanying locomotive diagram was that of a Beyer, Peacock- or Avonside-built engine with its rearward-located steam dome.[9]

The original CGR number of the locomotive is not known with certainty. Three locomotives which still appeared on the CGR roster in 1890, numbers 7, 9 and 14 as mentioned earlier (formerly numbers 21, 22 and 24), were no longer listed by year-end in 1896 and are the most likely candidates. It was possibly the Western System's no. 9 (ex no. W22), built by Avonside, since it is possible that a transcription error may have led to the number W22 being recorded as number M22.[8]

South African Railways

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (CGR, Natal Government Railways and Central South African Railways) were united under a single administration to control and administer the railways, ports and harbours of the Union. Even though the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways was only implemented with effect from 1 January 1912.[5][11]

By 1912, three of these locomotives survived on the CGR to be taken onto the SAR roster. They were considered obsolete by the SAR, designated Class 01 and renumbered by having the numeral 0 prefixed to their existing numbers. All of them were withdrawn from service by 1916.[1][2][11][12]

The engine no. 303 Bloemfontein of the CSAR was treated differently and was listed as excluded from the renumbering schedules. It was scrapped by the SAR in 1912.[11]

Works numbers and renumbering

Apart from the four which were sold to Sudan, all these locomotives were renumbered at times during the CGR era. By 1886, the system prefixes were dropped. By 1888, some official decided to start practicing gap-filling by renumbering numbers 21 to 24. Further renumbering, for reasons unknown, occurred by 1896 and 1904.[1][2][11]

The builders, works numbers, years in service, original numbers and known renumbering of these Cape 1st Class Moguls of 1876 are listed in the table.[1][2][11]

Nyasaland Railways myth

In his book Steam Locomotives of the South African Railways, Volume 1: 1859-1910, D.F. Holland states that two of these locomotives, numbers W12 and W16, by that time renumbered to 39 and 41 respectively, were sold to the Nyasaland Railways at some stage between 1904 and 1912.[1]

As with engines from some other early CGR locomotive classes which were supposedly sold to Nyasaland, this sale may be discounted as a myth which possibly began as a result of misinterpretation of entries in old and scant CGR records. The early locomotives in Nyasaland are well documented and no reference exists to locomotives which were obtained from the CGR. The first railway in Nyasaland was the Shire Highlands Railway (SHR), on which construction began in 1904 and which was opened in 1908. The second railway was the Central African Railway (CAR), on which Pauling & Co. began construction in 1913. Nyasaland Railways was only formed in 1930 to amalgamate the SHR and CAR.[7]

Illustration

In addition to the known numbering and renumbering, there appears to have been another CGR numbering system. Apart from photographic evidence, no information about this numbering system has been found as yet. In one of the examples depicted here, Beyer, Peacock-built no. 39, originally no. W12, bears the number 27 on the boiler just to the rear of the smokebox, which does not fit in with any of the known numbers of these locomotives. In the other, the same locomotive bears the number 15 in the same position aft of the smokebox. These numbers are therefore probably not the official engine numbers and may possibly even be boiler numbers, since a boiler number would migrate with a boiler during a boiler change. The same would probably be true about the numbers 7 and 18 aft of the smokebox on the other locomotives depicted.[2][11]

References

Wikimedia Commons has media related to CGR 1st Class 2-6-0 1876 BP.
  1. 1 2 3 4 5 6 7 8 9 10 11 12 Holland, D.F. (1971). Steam Locomotives of the South African Railways, Volume 1: 1859-1910 (1st ed.). Newton Abbott, Devon: David & Charles. pp. 28–29. ISBN 978-0-7153-5382-0.
  2. 1 2 3 4 5 6 C.G.R. Numbering Revised, Article by Dave Littley, SA Rail May–June 1993, pp. 94-95.
  3. ↑ Dulez, Jean A. (2012). Railways of Southern Africa 150 Years (Commemorating One Hundred and Fifty Years of Railways on the Sub-Continent - Complete Motive Power Classifications and Famous Trains - 1860-2011) (1st ed.). Garden View, Johannesburg, South Africa: Vidrail Productions. p. 36. ISBN 9 780620 512282.
  4. 1 2 3 4 5 Espitalier, T.J.; Day, W.A.J. (1943). The Locomotive in South Africa - A Brief History of Railway Development. Chapter II - The Adoption of the 3 ft. 6 in. Gauge on the Cape Government Railways. South African Railways and Harbours Magazine, July 1943. pp. 515-518.
  5. 1 2 3 The South African Railways - Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, p. 13.
  6. 1 2 3 Espitalier, T.J.; Day, W.A.J. (1944). The Locomotive in South Africa - A Brief History of Railway Development. Chapter II - The Cape Government Railways (Continued). South African Railways and Harbours Magazine, April 1944. pp. 253-257.
  7. 1 2 3 Intermediate CGR numbering system c. 1883-1888
  8. 1 2 3 True identity of CSAR no. 303 Bloemfontein
  9. 1 2 Espitalier, T.J.; Day, W.A.J. (1944). The Locomotive in South Africa - A Brief History of Railway Development. Chapter V - Other Transvaal and O.F.S. Railways. South African Railways and Harbours Magazine, December 1944. pp. 925, 927.
  10. ↑ Updated information on the 1st Class Kitsons
  11. 1 2 3 4 5 6 Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer's Office, Pretoria, January 1912, p. 26. (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)
  12. ↑ Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. p. 16. ISBN 0869772112.
This article is issued from Wikipedia - version of the 9/27/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.